- 您现在的位置：买卖IC网 > PDF目录1829 > LTC3421EUF#TRPBF (Linear Technology)IC REG BOOST SYNC ADJ 1.5A 24QFN PDF资料下载
参数资料
| 型号： | LTC3421EUF#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST SYNC ADJ 1.5A 24QFN |
| 标准包装： | 2,500 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 2.4 V ~ 5.25 V |
| 输入电压： | 0.5 V ~ 4.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 100kHz ~ 3MHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 24-QFN 裸露焊盘（4x4） |
LTC3421
OPERATIO
LOW VOLTAGE START-UP
The LTC3421 includes an independent start-up oscillator
designed to start-up at input voltages of 0.85V typical. The
frequency and peak current limit during start-up are inter-
nally controlled. The device can start-up under some load
(see graph of Start-Up Current vs Input Voltage). Soft-
start and inrush current limiting are provided during start-
up as well as normal mode. The same soft-start capacitor
is used for each operating mode.
When either V IN or V OUT exceeds 2.25V, the IC enters
normal operating mode. Once the output voltage exceeds
the input by 0.3V, the IC powers itself from V OUT instead
of V IN . At this point the internal circuitry has no depen-
dency on the V IN input voltage, eliminating the require-
ment for a large input capacitor. The input voltage can drop
as low as 0.5V without affecting circuit operation. The
limiting factor for the application becomes the availability
of the power source to supply sufficient energy to the
output at the low voltages and the maximum duty cycle,
which is clamped at 91% typical.
LOW NOISE FIXED FREQUENCY OPERATION
Shutdown
The part is shut down by pulling SHDN below 0.3V, and
activated by pulling the pin initially above 1V and maintain-
ing a high state down to 0.5V. Note that the SHDN pin can
be driven above V IN or V OUT as long as it is limited to less
than the absolute maximum rating.
Soft-Start
The soft-start time is programmed with an external capaci-
tor to ground on the SS pin. An internal current source
charges it with a nominal 2.5 μ A. The voltage on the SS pin
(in conjunction with the external resistor on the I LIM pin)
is used to control the peak current limit until the voltage on
the capacitor exceeds 1.6V, at which point the external
resistor sets the peak current. In the event of a com-
manded shutdown or a thermal shutdown, the capacitor is
Oscillator
The frequency of operation is set through a resistor from
the R T pin to ground. An internally trimmed timing capaci-
tor resides inside the IC. The oscillator can be synchro-
nized with an external clock applied to the SYNC pin. When
synchronizing the oscillator, the free running frequency
must be set to an approximately 30% lower frequency
than the desired synchronized frequency.
Current Sensing
Lossless current sensing converts the peak current signal
to a voltage to sum in with the internal slope compensa-
tion. This summed signal is compared to the error ampli-
fier output to provide a peak current control command for
the PWM. The slope compensation in the IC is adaptive to
the input voltage and output voltage. Therefore, the con-
verter provides the proper amount of slope compensation
to ensure stability, but not an excess to cause a loss of
phase margin in the converter.
Error Amplifier
The error amplifier is a transconductance amplifier, with
its positive input internally connected to the 1.22V refer-
ence and its negative input connected to FB. A simple
compensation network is placed from COMP to ground.
Internal clamps limit the minimum and maximum error
amplifier output voltage for improved large-signal tran-
sient response. During sleep (in Burst Mode operation),
the compensation pin is high impedance; however, clamps
limit the voltage on the external compensation network,
preventing the compensation capacitor from discharging
to zero during the sleep time.
Current Limit
The programmable current limit circuit sets the maximum
peak current. This clamp level is programmed with a
resistor from I LIM to ground. In Burst Mode operation, the
current limit is automatically set to a nominal value of 0.6A
peak for optimal efficiency.
discharged automatically. Note that Burst Mode operation
is inhibited during the soft-start time.
I LIM =
150
R
t(ms) = C SS ( μ F) ? 320
where I is in amps and R is in k ? .
3421f
8
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3422EDD#TRPBF | IC REG BOOST SYNC ADJ 1.5A 10DFN |
| LTC3424EMS#TR | IC REG BOOST SYNC ADJ 2A 10MSOP |
| LTC3425EUH#TRPBF | IC REG BOOST SYNC ADJ 5A 32QFN |
| LTC3426ES6#TRPBF | IC REG BOOST ADJ 2A TSOT23-6 |
| LTC3427EDC#TRPBF | IC REG BOOST SYNC ADJ 0.5A 6DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3422 | 制造商:LINER 制造商全称:Linear Technology 功能描述:1.5A, 3MHz Synchronous Step-Up DC/DC Converter with Output Disconnect |
| LTC3422EDD | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Up 0.5V to 4.5V 10-Pin DFN EP |
| LTC3422EDD#PBF | 功能描述:IC REG BOOST SYNC ADJ 1.5A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3422EDD#TRPBF | 功能描述:IC REG BOOST SYNC ADJ 1.5A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3423 | 制造商:LINEAR 制造商全称:LINEAR 功能描述:Low Output Voltage 3MHz Micropower Synchronous Boost Converters |
发布紧急采购，3分钟左右您将得到回复。