参数资料
| 型号： | LTC3424EMS#TR |
| 厂商： | Linear Technology |
| 文件页数： | 7/12页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST SYNC ADJ 2A 10MSOP |
| 标准包装： | 2,500 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.5 V ~ 5.5 V |
| 输入电压： | 0.5 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 3MHz |
| 电流 - 输出： | 2A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 10-MSOP |
| 其它名称： | LTC3424EMSTR |
LTC3423/LTC3424
APPLICATIO S I FOR ATIO
DETAILED DESCRIPTION
The LTC3423/LTC3424 provides high efficiency, low noise
power for applications such as portable instrumentation
and are ideal for applications that require an output voltage
between 1.5V and 2.6V from a single cell. These products
are an addition to the LTC3401 and LTC3402 family of
synchronous boost converters, with the differences being
the omission of the power good function (PGOOD) and the
addition of a V DD input to provide internal power. The IC
will not start up until the applied voltage on the V DD pin is
above 2.7V.
The current mode architecture with adaptive slope
compensation provides ease of loop compensation with
excellent transient load response. The low R DS(ON) , low
gate charge synchronous switches provides the pulse
width modulation control at high efficiency.
Zero Current Amp . The zero current amplifier monitors the
inductor current to the output and shuts off the synchro-
nous rectifier once the current is below 50mA, preventing
negative inductor current.
Burst Mode Operation
Burst Mode operation is when the IC delivers energy to the
output until it is regulated and then goes into a sleep mode
where the outputs are off and the IC is consuming only
38 μ A. In this mode, the output ripple has a variable
frequency component with load current and the steady
state ripple will be typically below 3%.
During the period where the device is delivering energy to
the output, the peak current will be equal to 400mA and the
inductor current will terminate at zero current for each cycle.
In this mode the maximum output current is given by:
Low Noise Fixed Frequency Operation
Oscillator . The frequency of operation is set through a
I OUT ( MAXBURST ) ≈
V IN
6 ? V OUT
Amps
resistor from the R t pin to ground where f = 3 ? 10 10 /R t . An
internally trimmed timing capacitor resides inside the IC.
The oscillator can be synchronized with an external clock
inserted on the MODE/SYNC pin. When synchronizing the
oscillator, the free running frequency must be set to
approximately 30% lower than the desired synchronized
frequency. Keeping the sync pulse width below 2 μ s will
ensure that Burst Mode operation is disabled.
Current Sensing . Lossless current sensing converts the
peak current signal to a voltage to sum in with the internal
slope compensation. This summed signal is compared to
the error amplifier output to provide a peak current control
Burst Mode operation is user controlled by driving the
MODE/SYNC pin high to enable and low to disable. It is
recommended that Burst Mode operation be entered after
the part has started up.
COMPONENT SELECTION
Inductor Selection
The high frequency operation of the LTC3423/LTC3424
allows the use of small surface mount inductors. The
minimum inductance value is proportional to the operat-
ing frequency and is limited by the following constraints:
L > μ H and L >
commandforthePWM.TheslopecompensationintheIC
is adaptive to the input and output voltage. Therefore, the
converter provides the proper amount of slope compensa-
tion to ensure stability and not an excess causing a loss of
phase margin in the converter.
k
f
where
V IN ( MIN ) ? ( V OUT ( MAX ) – V IN ( MIN )
f ? Ripple ? V OUT ( MAX )
)
H
Error Amp . The error amplifier is a transconductance
amplifier with g m = 85 μ mhos. A simple compensation
network is placed from the V C pin to ground.
Current Limit . The current limit amplifier will shut the
NMOS switch off once the current exceeds its threshold.
The current amplifier delay to output is typically 50ns.
k = 3 for LTC3423, 2 for LTC3424
f = Operating Frequency (Hz)
Ripple = Allowable Inductor Current Ripple (A)
V IN(MIN) = Minimum Input Voltage (V)
V OUT(MAX) = Maximum Output Voltage (V)
34234f
7
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3425EUH#TRPBF | IC REG BOOST SYNC ADJ 5A 32QFN |
| LTC3426ES6#TRPBF | IC REG BOOST ADJ 2A TSOT23-6 |
| LTC3427EDC#TRPBF | IC REG BOOST SYNC ADJ 0.5A 6DFN |
| LTC3428EDD#TRPBF | IC REG BOOST ADJ 4A 10DFN |
| LTC3429ES6#TRM | IC REG BST SYNC ADJ .6A TSOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3425 | 制造商:LINER 制造商全称:Linear Technology 功能描述:5A, 8MHz, 4-Phase Synchronous Step-Up DC/DC Converter |
| LTC3425EUH | 功能描述:IC REG BOOST SYNC ADJ 5A 32QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3425EUH#PBF | 功能描述:IC REG BOOST SYNC ADJ 5A 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3425EUH#TR | 功能描述:IC REG BOOST SYNC ADJ 5A 32QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3425EUH#TRPBF | 功能描述:IC REG BOOST SYNC ADJ 5A 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。