参数资料
| 型号： | LTC3424EMS#TR |
| 厂商： | Linear Technology |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST SYNC ADJ 2A 10MSOP |
| 标准包装： | 2,500 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.5 V ~ 5.5 V |
| 输入电压： | 0.5 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 3MHz |
| 电流 - 输出： | 2A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 10-MSOP |
| 其它名称： | LTC3424EMSTR |
LTC3423/LTC3424
APPLICATIO S I FOR ATIO
R 6 ≈ ? FF IN
? – R 5
Operating Frequency Selection
There are several considerations in selecting the operat-
ing frequency of the converter. The first is determining the
sensitive frequency bands that cannot tolerate any spec-
tral noise. For example, in products incorporating RF
communications, the 455kHz IF frequency is sensitive to
any noise, therefore switching above 600kHz is desired.
Some communications have sensitivity to 1.1MHz. In this
case, converter frequencies up to 3MHz may be em-
ployed.
The second consideration is the physical size of the
converter. As the operating frequency goes up, the induc-
tor and filter caps go down in value and size. The trade off
is in efficiency since the switching losses due to gate
charge are going up proportional with frequency.
130mA/100mV, and the LTC3424 is typically 170mA/
100mV, so the amount of signal injected is proportional to
the anticipated change of inductor current with load. The
outer voltage loop performs the remainder of the correc-
tion, but because of the load feed forward signal, the range
over which it must slew is greatly reduced. This results in
an improved transient response. A logic level feed forward
signal, V FF , is coupled through components C5 and R6.
The amount of feed forward signal is attenuated with
resistor R6 and is given by the following relationship:
? V ? R5 ? V ? 1.5 ?
? V OUT ? ? I OUT ?
where ? I OUT = load current change.
Another operating frequency consideration is whether the
application can allow “pulse skipping.” In this mode, the
V IN
V OUT
minimum on time of the converter cannot support the duty
cycle, so the converter ripple will go up and there will be
V DD
IN
6
LTC3423/LTC3424
V DD SW
4
a low frequency component of the output ripple. In many
10
SHDN
V OUT
7
applications where physical size is the main criterion then
running the converter in this mode is acceptable. In
applications where it is preferred not to enter this mode,
3
2
V IN FB
MODE/SYNC V C
8
9
then the maximum operating frequency is given by:
1
R t
GND
5
C3
f MAX _ NOSKIP
=
V OUT – V IN
V OUT ? t ON ( MIN )
Hz
LOAD FEED
R6
R5
C5
3.3nF
where t ON(MIN) = minimum on time = 140ns
Reducing Output Capacitance with a Load Feed
FORWARD
SIGNAL
V FF
Figure 2
3423/24 F02
Forward Signal
In many applications the output filter capacitance can be
reduced for the desired transient response by having the
device commanding the change in load current, (i.e.
system microcontroller), inform the power converter of
the changes as they occur. Specifically, a “load feed
forward” signal coupled into the V C pin gives the inner
current loop a head start in providing the change in output
current. The transconductance of the LTC3423 converter
at the V C pin with respect to the inductor current is typically
Closing the Feedback Loop
The LTC3423/LTC3424 uses current mode control with
internal adaptive slope compensation. Current mode con-
trol eliminates the 2nd order filter due to the inductor and
output capacitor exhibited in voltage mode controllers,
and simplifies it to a single-pole filter response. The
product of the modulator control to output DC gain plus
the error amp open-loop gain equals the DC gain of the
system.
34234f
9
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3425EUH#TRPBF | IC REG BOOST SYNC ADJ 5A 32QFN |
| LTC3426ES6#TRPBF | IC REG BOOST ADJ 2A TSOT23-6 |
| LTC3427EDC#TRPBF | IC REG BOOST SYNC ADJ 0.5A 6DFN |
| LTC3428EDD#TRPBF | IC REG BOOST ADJ 4A 10DFN |
| LTC3429ES6#TRM | IC REG BST SYNC ADJ .6A TSOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3425 | 制造商:LINER 制造商全称:Linear Technology 功能描述:5A, 8MHz, 4-Phase Synchronous Step-Up DC/DC Converter |
| LTC3425EUH | 功能描述:IC REG BOOST SYNC ADJ 5A 32QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3425EUH#PBF | 功能描述:IC REG BOOST SYNC ADJ 5A 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3425EUH#TR | 功能描述:IC REG BOOST SYNC ADJ 5A 32QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3425EUH#TRPBF | 功能描述:IC REG BOOST SYNC ADJ 5A 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。