- 您现在的位置：买卖IC网 > PDF目录14013 > LTC3523EUD-2#PBF (Linear Technology)IC REG BUCK BOOST SYNC ADJ 16QFN PDF资料下载
参数资料
| 型号： | LTC3523EUD-2#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK BOOST SYNC ADJ 16QFN |
| 标准包装： | 121 |
| 类型： | 降压（降压），升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 0.62 V ~ 5.5 V |
| 输入电压： | 1.8 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 2.4MHz |
| 电流 - 输出： | 400mA，600mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 16-QFN-EP（3x3） |
LTC3523/LTC3523-2
APPLICATIONS INFORMATION
frequency ferrite core inductor materials reduce frequency
dependent power losses compared to cheaper powdered
iron types, improving ef?ciency. The inductor should have
low ESR (series resistance of the windings) to reduce the
I 2 R power losses, and must be able to handle the peak
inductor current without saturating. Molded chokes and
some chip inductors usually do not have enough core to
support the peak inductor currents of 1000mA seen on
the LTC3523/LTC3523-2. To minimize radiated noise, use
a toroid, pot core or shielded bobbin inductor. See Table
1 for suggested inductors and suppliers.
Step-Up: For the step-up converter a minimum inductance
value of 3.3μH is recommended for 3.6V and lower output
voltage applications, and a 4.7μH for output voltages
greater than 3.6V. Larger values of inductance will allow
greater output current capability by reducing the inductor
ripple current. Increasing the inductance above 10μH will
increase size while providing little improvement in output
current capability.
Step-Down: For most applications, the value of the inductor
will fall in the range of 3.3μH to 10μH, depending upon
the amount of current ripple desired. A reasonable point
to start is to set the current ripple at 30% of the output
current.
Note that larger values of inductance will allow greater
output current capability by reducing the inductor ripple
Table 1. Recommended Inductors
current. Increasing the inductance above 10μH will increase
size while providing little improvement in output current
capability. A 4.7μH inductor will work well for most Li-Ion
or 2-cell alkaline/NiMH cell applications
Output and Input Capacitor Selection
Low ESR (equivalent series resistance) capacitors should
be used to minimize the output voltage ripple. Multilayer
ceramic capacitors are an excellent choice as they have
extremely low ESR and are available in small footprints.
Step-Up: A 2.2μF to 10μF output capacitor is suf?cient for
most applications. Larger values up to 22μF may be used
to obtain extremely low output voltage ripple and improve
transient response. An additional phase lead capacitor con-
nected between V OUT and FB1 may be required with output
capacitors larger than 10μF to maintain acceptable phase
margin. X5R and X7R dielectric materials are preferred
for their ability to maintain capacitance over wide voltage
and temperature ranges.
Step-Down: Low ESR input capacitors reduce input
switching noise and reduce the peak current drawn from
the battery. It follows that ceramic capacitors are also a
good choice for input decoupling and should be located
as close as possible to the device. Table 2 shows the
range of acceptable capacitors for a given programmed
output voltage. Minimum capacitance values in the table
PART
ME3220
LPS3010
DO2010
SD3112
MIP3226D
LQH32CN
LQH2MC
CDRH3D16
CDRH2D14
NR3010
NR3015
L (μH)
4.7 to 15
4.7 to 10
4.7 to 15
4.7 to 15
4.7 to 10
4.7 to 15
4.7 to 15
4.7 to 15
4.7 to 12
4.7 to 15
4.7 to 15
MAXIMUM CURRENT
(mA)
1200 to 700
720 to 510
800 to 510
740 to 405
600 to 200
650 to 300
300 to 200
900 to 450
680 to 420
750 to 400
1000 to 560
DCR ( Ω )
0.19 to 0.52
0.3 to 0.54
0.8 to 1.84
0.25 to 0.65
0.1 to 0.16
0.15 to 0.58
0.8 to 1.6
0.11 to 0.29
0.12 to 0.32
0.19 to 0.74
0.12 to 0.36
DIMENSIONS (mm)
(L × W × H)
3.2 × 2.5 × 2.0
3.0 × 3.0 × 1.0
2.0 × 2.0 × 1.0
3.1 × 3.1 × 1.2
3.2 × 2.6 × 1.0
3.2 × 2.5 × 1.5
2 × 1.6 × 0.9
3.8 × 3.8 × 1.8
3.2 × 3.2 × 1.5
3.0 × 3.0 × 1.0
3.0 × 3.0 × 1.5
MANUFACTURER
Coil Craft
www.coilcraft.com
Cooper
www.cooperet.com
FDK
www.fdk.com
Murata
www.murata.com
Sumida
www.sumida.com
Taiyo Yuden
www.t-yuden.com
3523fb
10
相关PDF资料 |
PDF描述 |
|---|---|
| V28C24C100BG2 | CONVERTER MOD DC/DC 24V 100W |
| LTC3527EUD-1#PBF | IC REG BOOST SYNC ADJ DL 16QFN |
| V28C24C100BF3 | CONVERTER MOD DC/DC 24V 100W |
| LTC3527EUD#PBF | IC REG BOOST SYNC ADJ DL 16QFN |
| MAX6717AUKZWD6+T | IC SUPERVISOR MPU SOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3523EUD-2-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Synchronous 600mA Step-Up and 400mA Step-Down DC/DC Converters |
| LTC3523EUD-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Synchronous 600mA Step-Up and 400mA Step-Down DC/DC Converters |
| LTC3523EUD-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Synchronous 600mA Step-Up and 400mA Step-Down DC/DC Converters |
| LTC3524 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Adjustable TFT Bias Supply with WLED Driver |
| LTC3524EUF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Adjustable TFT Bias Supply with WLED Driver |
发布紧急采购，3分钟左右您将得到回复。