- 您现在的位置：买卖IC网 > PDF目录80267 > LTC3554EPD#PBF (LINEAR TECHNOLOGY CORP) 0.6 A BATTERY CHARGE CONTROLLER, 2590 kHz SWITCHING FREQ-MAX, PQCC20 PDF资料下载
参数资料
| 型号： | LTC3554EPD#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 0.6 A BATTERY CHARGE CONTROLLER, 2590 kHz SWITCHING FREQ-MAX, PQCC20 |
| 封装： | 3 X 3 MM, LEAD FREE, PLASTIC, UTQFN-20 |
| 文件页数： | 14/36页 |
| 文件大小： | 418K |
| 代理商： | LTC3554EPD#PBF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTC3554/LTC3554-2
21
35542fb
PGOOD Operation
The PGOOD pin is an open-drain output which indicates
that all enabled step-down switching regulators have
reached their nal regulation voltage. It goes high-imped-
ance 230ms after all enabled switching regulators reach
92% of their regulation value. The delay allows ample time
for an external processor to reset itself. PGOOD may be
used as a power-on reset to a microprocessor powered
by the step-down switching regulators. Since PGOOD is
an open-drain output, a pull-up resistor to an appropriate
power source is needed. A suggested approach is to con-
nect the pull-up resistor to one of the step-down switching
regulator output voltages so that power is not dissipated
while the regulators are disabled.
In hard reset, the PGOOD pin is placed in high impedance
state to minimize current draw from the battery in this
ultralow power state. This will cause the PGOOD pin to
signal the wrong state (high level) if it is pulled up to a
supply that is not shut down in hard reset (e.g. BAT). If
PGOOD is pulled up to one of the step-down switching
regulator outputs then the PGOOD pin will indicate the
correct state (low level) in hard reset because the switch-
ing regulator output will be low.
Normal Operating Mode (STBY Pin Low)
In normal mode (STBY pin low), the regulators perform
as traditional constant-frequency current mode switch-
ing regulators. Switching frequency is determined by an
internal oscillator whose frequency is selectable via the
FSEL pin. An internal latch is set at the start of every
oscillator cycle, turning on the main P-channel MOSFET
switch. During each cycle, a current comparator compares
the inductor current to the output of an error amplier.
The output of the current comparator resets the internal
latch, which causes the main P-channel MOSFET switch
to turn off and the N-channel MOSFET synchronous
rectier to turn on. The N-channel MOSFET synchronous
rectier turns off at the end of the clock cycle, or when
the current through the N-channel MOSFET synchronous
rectier drops to zero, whichever happens rst. Via this
mechanism, the error amplier adjusts the peak inductor
current to deliver the required output power. All neces-
sary compensation is internal to the step-down switching
regulator requiring only a single ceramic output capacitor
for stability.
At light load and no-load conditions, the buck automatically
switches to a power-saving hysteretic control algorithm
that operates the switches intermittently to minimize
switching losses. Known as Burst Mode operation, the
buck cycles the power switches enough times to charge
the output capacitor to a voltage slightly higher than
the regulation point. The buck then goes into a reduced
quiescent current sleep mode. In this state, power loss is
minimized while the load current is supplied by the output
capacitor. Whenever the output voltage drops below a
predetermined value, the buck wakes from sleep and cycles
the switches again until the output capacitor voltage is once
again slightly above the regulation point. Sleep time thus
depends on load current, since the load current determines
the discharge rate of the output capacitor.
Standby Mode (STBY Pin High)
There are situations where even the low quiescent current
of Burst Mode operation is not low enough. For instance,
in a static memory keep alive situation, load current may
fall well below 1μA. In this case, the 25μA typical BVIN
quiescent current per active regulator in Burst Mode
operation becomes the main factor determining battery
run time.
Standby mode cuts BVIN quiescent current down to just
1.5μA per active regulator, greatly extending battery run
time in this essentially no-load region of operation. The
application circuit commands the LTC3554 into and out
of standby mode via the STBY pin logic input. Bringing
the STBY pin high places both regulators into standby
mode, while bringing it low returns them to Burst Mode
operation. In standby mode, load capability drops to 5mA
per regulator.
OPERATION
相关PDF资料 |
PDF描述 |
|---|---|
| LM4040A82IDCKT | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 8.192 V, PDSO6 |
| LT1021BMH-5#PBF | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 5 V, MBCY8 |
| LC015B | DC-DC REG PWR SUPPLY MODULE |
| LM385M-2.5X | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, PDSO8 |
| LM2575S-ADJTR | 3.2 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, PSSO5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3554EPDTRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Micropower USB Power Manager with Li-Ion Charger and Two Step-Down Regulators |
| LTC3554EUD#PBF | 功能描述:IC USB POWER MANAGER 20UTQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:热电冷却器 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.173"，4.40mm 宽）裸露焊盘 供应商设备封装:28-TSSOP 裸露焊盘 包装:管件 产品目录页面:1410 (CN2011-ZH PDF) |
| LTC3554EUD#TRPBF | 功能描述:IC USB POWER MANAGER 20UTQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:PowerPath™ 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LTC3554EUD-1#PBF | 功能描述:IC USB POWER MANAGER 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:PowerPath™ 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LTC3554EUD-1#TRPBF | 功能描述:IC USB POWER MANAGER 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:PowerPath™ 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
发布紧急采购，3分钟左右您将得到回复。