- 您现在的位置：买卖IC网 > PDF目录79697 > LTC3565IDD#TRPBF (LINEAR TECHNOLOGY CORP) 2.5 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PDSO10 PDF资料下载
参数资料
| 型号： | LTC3565IDD#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 2.5 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封装： | 3 X 3 MM, LEAD FREE, PLASTIC, MO-229WEED-2, DFN-10 |
| 文件页数： | 8/22页 |
| 文件大小： | 587K |
| 代理商： | LTC3565IDD#TRPBF |
LTC3565
3565fa
Although a buck regulator is capable of providing the full
output current in dropout, it should be noted that as the
inputvoltageVINdropstowardVOUT,theloadstepcapability
does decrease due to the decreasing voltage across the
inductor. Applications that require large load step capabil-
ity near dropout should use a different topology such as
SEPIC, Zeta or single inductor, positive buck/boost.
Insomeapplications,amoreseveretransientcanbecaused
byswitchinginloadswithlarge(>1F)inputcapacitors.The
discharged input capacitors are effectively put in parallel
with COUT, causing a rapid drop in VOUT. No regulator can
deliverenoughcurrenttopreventthisproblem,iftheswitch
connectingtheloadhaslowresistanceandisdrivenquickly.
The solution is to limit the turn-on speed of the load switch
driver. A Hot Swap controller is designed specifically for
this purpose and usually incorporates current limiting,
short-circuit protection, and soft-starting.
Efficiency Considerations
The percent efficiency of a switching regulator is equal to
the output power divided by the input power times 100%.
It is often useful to analyze individual losses to determine
what is limiting the efficiency and which change would
produce the most improvement. Percent efficiency can
be expressed as:
%Efficiency = 100% – (L1 + L2 + L3 + ...)
where L1, L2, etc. are the individual losses as a percent-
age of input power.
Although all dissipative elements in the circuit produce
losses, four main sources usually account for most of
the losses in LTC3565 circuits: 1) LTC3565 VIN current,
2) switching losses, 3) I2R losses, 4) other losses.
1) The VIN current is the DC supply current given in the
electrical characteristics which excludes MOSFET driver
andcontrolcurrents.VINcurrentresultsinasmall(<0.1%)
loss that increases with VIN, even at no load.
2) The switching current is the sum of the MOSFET driver
and control currents. The MOSFET driver current results
fromswitchingthegatecapacitanceofthepowerMOSFETs.
Each time a MOSFET gate is switched from low to high
to low again, a packet of charge dQ moves from VIN to
ground. The resulting dQ/dt is a current out of VIN that is
typically much larger than the DC bias current. In continu-
ous mode, IGATECHG = fO(QT + QB), where QT and QB are
the gate charges of the internal top and bottom MOSFET
switches. The gate charge losses are proportional to VIN
and thus their effects will be more pronounced at higher
supply voltages.
3) I2R losses are calculated from the DC resistances of
the internal switches, RSW, and external inductor, RL. In
continuous mode, the average output current flowing
through inductor L is “chopped” between the internal top
and bottom switches. Thus, the series resistance look-
ing into the SW pin is a function of both top and bottom
MOSFET RDS(ON) and the duty cycle (DC) as follows:
RSW = (RDS(ON)TOP)(DC) + (RDS(ON)BOT)(1 – DC)
The RDS(ON) for both the top and bottom MOSFETs can
be obtained from the Typical Performance Characteristics
curves. Thus, to obtain I2R losses:
I2R losses = IOUT2(RSW + RL)
4) Other “hidden” losses such as copper trace and internal
battery resistances can account for additional efficiency
degradations in portable systems. It is very important
to include these “system” level losses in the design of a
system. The internal battery and fuse resistance losses can
be minimized by making sure that CIN has adequate charge
storage and very low ESR at the switching frequency. Other
applications inForMation
Figure 3. Power Loss vs Load Currrent
LOAD CURRENT (mA)
VOUT = 1.2V
VOUT = 1.5V
VOUT = 1.8V
0.0001
POWER
LOSS
(W)
0.001
1
0.1
1
10
100
1000
10000
3565 F05
0.01
0.1
VIN = 3.6V
fO = 1MHz
VOUT = 1.2V - 1.8V
相关PDF资料 |
PDF描述 |
|---|---|
| LS75-12 | 1-OUTPUT DC-DC UNREG PWR SUPPLY MODULE |
| LED15-48S05W | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| LFFSWG-TTL-70F | SQUARE, 0.07 MHz, WAVEFORM GENERATION, PDIP4 |
| LFFSWG-TTL-55J | SQUARE, 0.055 MHz, WAVEFORM GENERATION, PDSO4 |
| LH2540-2-V3 | 2-OUTPUT 51 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3565IMSE | 制造商:LINER 制造商全称:Linear Technology 功能描述:1.25A, 4MHz, Synchronous Step-Down DC/DC Converter |
| LTC3565IMSE#PBF | 功能描述:IC REG BUCK SYNC ADJ 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3565IMSE#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3565IMSEPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:1.25A, 4MHz, Synchronous Step-Down DC/DC Converter |
| LTC3565IMSE-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:1.25A, 4MHz, Synchronous Step-Down DC/DC Converter |
发布紧急采购，3分钟左右您将得到回复。