- 您现在的位置：买卖IC网 > PDF目录80091 > LTC3568IDD#PBF (LINEAR TECHNOLOGY CORP) 4 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PDSO10 PDF资料下载
参数资料
| 型号： | LTC3568IDD#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 4 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封装： | 3 X 3 MM, LEAD FREE, PLASTIC, MO-229WEED-2, DFN-10 |
| 文件页数： | 2/18页 |
| 文件大小： | 300K |
| 代理商： | LTC3568IDD#PBF |
LTC3568
0
3568fa
Ceramic capacitors have the lowest ESR and cost but also
have the lowest capacitance density, a high voltage and
temperature coefficient and exhibit audible piezoelectric
effects. In addition, the high Q of ceramic capacitors along
with trace inductance can lead to significant ringing. Other
capacitor types include the Panasonic specialty polymer
(SP) capacitors.
In most cases, 0.1F to 1F of ceramic capacitors should
also be placed close to the LTC3568 in parallel with the
main capacitors for high frequency decoupling.
CeramicInputandOutputCapacitors
Higher value, lower cost ceramic capacitors are now be-
coming available in smaller case sizes. These are tempting
for switching regulator use because of their very low ESR.
Unfortunately, the ESR is so low that it can cause loop
stabilityproblems.SolidtantalumcapacitorESRgenerates
aloop“zero”at5kHzto50kHzthatisinstrumentalingiving
acceptable loop phase margin. Ceramic capacitors remain
capacitive to beyond 300kHz and ususally resonate with
their ESL before ESR becomes effective. Also, ceramic
caps are prone to temperature effects which requires the
designer to check loop stability over the operating tem-
perature range. To minimize their large temperature and
voltage coefficients, only X5R or X7R ceramic capacitors
should be used. A good selection of ceramic capacitors
is available from Taiyo Yuden, TDK and Murata.
Great care must be taken when using only ceramic input
and output capacitors. When a ceramic capacitor is used
at the input and the power is being supplied through long
wires, such as from a wall adapter, a load step at the output
can induce ringing at the VIN pin. At best, this ringing can
couple to the output and be mistaken as loop instability.
At worst, the ringing at the input can be large enough to
damage the part.
Since the ESR of a ceramic capacitor is so low, the input
and output capacitor must instead fulfill a charge storage
requirement.Duringaloadstep,theoutputcapacitormust
instantaneously supply the current to support the load
until the feedback loop raises the switch current enough
to support the load. The time required for the feedback
loop to respond is dependent on the compensation com-
ponents and the output capacitor size. Typically, 3 to 4
cycles are required to respond to a load step, but only in
the first cycle does the output drop linearly. The output
droop, VDROOP, is usually about 2 to 3 times the linear
drop of the first cycle. Thus, a good place to start is with
the output capacitor size of approximately:
C
I
f V
OUT
O
DROOP
≈
Δ
2 5
.
More capacitance may be required depending on the duty
cycle and load step requirements.
Inmostapplications,theinputcapacitorismerelyrequired
to supply high frequency bypassing, since the impedance
to the supply is very low. A 22F ceramic capacitor is
usually enough for these conditions.
SettingtheOutputVoltage
The LTC3568 develops a 0.8V reference voltage between
the feedback pin, VFB, and the signal ground as shown in
Figure 5. The output voltage is set by a resistive divider
according to the following formula:
V
R
OUT ≈
+
0 8 1
2
1
.
Keeping the current small (<5A) in these resistors maxi-
mizes efficiency, but making them too small may allow
stray capacitance to cause noise problems and reduce the
phase margin of the error amp loop.
Toimprovethefrequencyresponse,afeed-forwardcapaci-
tor CF may also be used. Great care should be taken to
route the VFB line away from noise sources, such as the
inductor or the SW line.
ShutdownandSoft-Start
The SHDN/RT pin is a dual purpose pin that sets the oscil-
lator frequency and provides a means to shut down the
LTC3568. This pin can be interfaced with control logic in
several ways, as shown in Figure 3(a) and Figure 3(b).
The ITH pin is primarily for loop compensation, but it can
also be used to increase the soft-start time. Soft start
reduces surge currents from VIN by gradually increasing
the peak inductor current. Power supply sequencing can
also be accomplished using this pin. The LTC3568 has an
applicaTions inForMaTion
相关PDF资料 |
PDF描述 |
|---|---|
| LES015YH21N | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| LES015YJ18N | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| LES015YJ4N | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| LES015ZG38N | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| LM2320-7ERD2HF | 2-OUTPUT 50 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3569 | 制造商:LINER 制造商全称:Linear Technology 功能描述:7-Channel Confi gurable High Power PMIC |
| LTC3569EFE | 制造商:Linear Technology 功能描述:DC/DC Converter Chip |
| LTC3569EFE#PBF | 功能描述:IC REG BUCK SYNC ADJ 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3569EFE#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3569EFE-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Triple Buck Regulator With 1.2A and Two 600mA Outputs and Individual Programmable References |
发布紧急采购，3分钟左右您将得到回复。