参数资料
型号: LTC3569EFE#PBF
厂商: LINEAR TECHNOLOGY CORP
元件分类: 稳压器
英文描述: 2.5 A SWITCHING REGULATOR, 3000 kHz SWITCHING FREQ-MAX, PDSO16
封装: 4.40 MM, LEAD FREE, PLASTIC, TSSOP-16
文件页数: 4/26页
文件大小: 468K
代理商: LTC3569EFE#PBF
LTC3569
12
3569fd
OPERATION
600mA; two independent regulators at 1.2A each, where
regulator 3 is placed in slave mode to regulator 2 and
regulator 1 operates independently; or one 1.8A regula-
tor and a second 600mA regulator, where regulator 2 is
placed in slave mode to regulator 1, and regulator 3 is
independent.
When regulator 2 is operating as a slave, pull pins EN2 and
FB2 up to SVIN to enable the slave power stage. Likewise
when regulator 3 is operated as a slave, pull pins EN3 and
FB3 up to SVIN to enable the slave power stage. If the EN
pin of the slave device is pulled low, then the slave power
stage is disabled and that SW pin is Hi-Z.
Shutdown and Soft-Start
ThemaincontrolloopisshutdownafterpullingtheENxpin
to ground and waiting for the tOFF delay period to expire.
When in shutdown, but not in slave mode, a 2k resistor
to PGND discharges the output capacitor. When all three
regulators are turned off the LTC3569 enters low power
shutdown where all functions are disabled, and quiescent
current drops to below 1A.
A soft-start is enabled when any buck is initially turned
on, or following a thermal shutdown. Soft-start ramps the
programmedinternalreferenceatarateofabout0.75V/ms.
The output voltage follows the internal reference voltage
ramp throughout the soft-start period. While in soft-start,
the LTC3569 is forced into pulse-skipping mode until the
PGOOD flag indicates that the output voltage is nearing
the programmed regulation voltage. Once the PGOOD flag
has tripped, if the MODE pin is high the regulator then
operates in Burst Mode, otherwise the LTC3569 continues
to operate in pulse-skipping mode.
Thermal Protection
If the die junction temperature exceeds 150°C, a thermal
shutdown circuit disables all functions in the LTC3569,
and the SW nodes will be pulled low with 2k pull-downs.
After the die temperature drops below 125°C the LTC3569
restartswithoutchangingtheprogrammedreferencevolt-
age DAC; but a soft-start is initiated upon exiting thermal
shutdown.
PGOOD Pin
ThePGOODpinisanopen-drainoutputthatindicateswhen
all of the enabled regulator’s output voltages have risen to
within 92% of their programmed levels. The three bucks
each have separate PGOOD comparators with hysteresis.
The PGOOD flag drops if one of the enabled regulator’s
output voltages drops below 88% of the programmed
level. Output voltage transient drops of duration less than
2s are blanked and not reported at the PGOOD pin. The
PGOOD pin open-drain driver is disabled if PGOOD is
pulled up to a voltage above SVIN.
Programming the Reference
The full-scale reference voltage for each regulator is 0.8V.
The reference can be programmed in –25mV steps by
toggling the respective EN pin up to 15 times for a range
from800mVdownto425mV.ThisisillustratedinFigure3.
The EN pins require a minimum pulse width of 60ns, but
no more than 55s, as the toggle counter times out after
the EN pin remains high for around 125s (tEN). After the
tEN timeout, the counter state is latched and sent on to
the reference voltage DAC, and the counter is reset to full
scale. If the EN pin begins to toggle again, the counter
decrements on each falling edge. If the EN pin is toggled
more than 15 times, the counter remains fixed at the
lowest DAC reference level. To reprogram the DAC to full
scale, hold the EN pin low for 170s (tOFF), turning off the
buck, and then pull EN high once. The buck then initiates
a soft-start as VREF ramps up to the full-scale value.
If the DAC is reprogrammed without forcing a shutdown,
the soft-start ramp is not engaged and the reference
steps to the new value. Avoid using the full-scale 0.8V
reference in programmable output voltage applications
if the application cannot tolerate the transition through
shutdownandsoft-startwhenswitchingbetweendifferent
reference levels.
相关PDF资料
PDF描述
LTC4224CMS-2#TRMPBF 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10
LM4041CIM-1.2Y 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.225 V, PDSO8
LT3653IDCB#PBF 1.2 A BATTERY CHARGE CONTROLLER, 1650 kHz SWITCHING FREQ-MAX, PDSO8
LTC3388IDD-3#PBF 0.21 A SWITCHING REGULATOR, PDSO10
LM329CH#TRPBF 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 6.9 V, MBCY2
相关代理商/技术参数
参数描述
LTC3569EFE-TRPBF 制造商:LINER 制造商全称:Linear Technology 功能描述:Triple Buck Regulator With 1.2A and Two 600mA Outputs and Individual Programmable References
LTC3569EUD#PBF 功能描述:IC REG BUCK SYNC ADJ TRPL 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压(降压) 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON(1.45x1) 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2
LTC3569EUD#TRPBF 功能描述:IC REG BUCK SYNC ADJ TRPL 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压(降压) 输出类型:固定 输出数:1 输出电压:1.2V,1.5V,1.8V,2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP,10-MSOP(0.118",3.00mm 宽)裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘
LTC3569EUDC#PBF 功能描述:IC REG BUCK SYNC ADJ TRPL 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压(降压) 输出类型:固定 输出数:1 输出电压:1.2V,1.5V,1.8V,2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP,10-MSOP(0.118",3.00mm 宽)裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘
LTC3569EUDC#TRPBF 功能描述:IC REG BUCK SYNC ADJ TRPL 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压(降压) 输出类型:固定 输出数:1 输出电压:1.2V,1.5V,1.8V,2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP,10-MSOP(0.118",3.00mm 宽)裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘