- 您现在的位置：买卖IC网 > PDF目录14798 > LTC3602EFE#PBF (Linear Technology)IC REG BUCK SYNC ADJ 16TSSOP PDF资料下载
参数资料
| 型号： | LTC3602EFE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 16TSSOP |
| 标准包装： | 95 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 9.5 V |
| 输入电压： | 4.5 V ~ 10 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 1MHz |
| 电流 - 输出： | 2.5A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 16-TSSOP-EP |
| 产品目录页面： | 1335 (CN2011-ZH PDF) |
LTC3602
APPLICATIONS INFORMATION
V BURST =
+ 0 . 42 V
Burst Clamp Programming
If the voltage on the SYNC/MODE pin is less than INTV CC
by 1V or more, Burst Mode operation is enabled. During
Burst Mode operation, the voltage on the SYNC/MODE
pin determines the burst clamp level. This level sets the
minimum peak inductor current, I BURST , for each switching
cycle according to the following equation:
I BURST
6 A / V
V BURST is the voltage on the SYNC/MODE pin. I BURST can
be programmed in the range of 0A to 3.5A, which cor-
responds to a V BURST range of 0.42V to 1V. As the output
load current drops, the peak inductor current decreases
to keep the output voltage in regulation. When the output
load current demands a peak inductor current that is less
than I BURST , the burst clamp will force the peak inductor
current to remain equal to I BURST regardless of further
reductions in the load current. Since the average inductor
current is therefore greater than the output load current,
the voltage on the I TH pin will decrease. When the I TH
voltage drops to 330mV, sleep mode is enabled in which
both power MOSFETs are shut off along with most of the
circuitry to minimize power consumption. All circuitry is
turned back on and the power MOSFETs begin switching
again when the output voltage drops out of regulation. The
value for I BURST is determined by the desired amount of
output voltage ripple. As the value of I BURST increases, the
sleep time between pulses and the output voltage ripple
increases. The burst clamp voltage, V BURST , can be set
by a resistor divider from the INTV CC pin. Alternatively,
the SYNC/MODE pin may be tied directly to the V FB pin to
set V BURST = 0.6V (I BURST = 1A), or through an additional
divider resistor (R3) to set V BURST = 0.46V to 0.6V (see
Figure 2).
Pulse-skipping, which is a compromise between low output
voltage ripple and ef?ciency, can be implemented by con-
necting the SYNC/MODE pin to ground. This sets I BURST to
0A. In this condition, the peak inductor current is limited by
the minimum on-time of the current comparator and the
lowest output voltage ripple is achieved while still opera-
ting discontinuously. During very light output loads,
pulse-skipping allows only a few switching cycles to be
skipped while maintaining the output voltage in regulation.
Frequency Synchronization
The LTC3602’s internal oscillator can be synchronized
to an external clock signal. During synchronization, the
top MOSFET turn-on is locked to the falling edge of the
external frequency source. The synchronization frequency
range is 300kHz to 3MHz. Synchronization only occurs if
the external frequency is greater than the frequency set by
the R T resistor. Because slope compensation is generated
by the oscillator’s internal ramp, the external frequency
should be set 25% higher than the frequency set by the
R T resistor to ensure that adequate slope compensation
is present. When synchronized, the LTC3602 will operate
in pulse-skipping mode.
INTV CC Regulator
The LTC3602 features an integrated P-channel low dropout
linear regulator (LDO) that supplies power to the INTV CC
supply pin from the PV IN pin. This LDO supply has been
designed to deliver up to 35mA of load current for the
powering of the internal gate drivers and other internal
circuitry. A small external load may also be applied provided
that the total current from the INTV CC supply does not
exceed 35mA. The INTV CC pin should be bypassed with
no less than a 0.22μF ceramic capacitor. A 1μF ceramic
capacitor is suitable for most applications.
R2
INTV CC
FB
V OUT
LTC3602
R2
LTC3602
R3 (OPTIONAL)
SYNC/MODE
SGND
V BURST = 0.46V TO 1V
R1
SYNC/MODE
SGND
3602 F02
V BURST = 0.46V TO 0.6V
R1
Figure 2. Programing the Burst Clamp
3602fb
11
相关PDF资料 |
PDF描述 |
|---|---|
| ESC20DREH-S13 | CONN EDGECARD 40POS .100 EXTEND |
| ECC25DREF-S13 | CONN EDGECARD 50POS .100 EXTEND |
| LT1373IS8#PBF | IC REG MULTI CONFIG ADJ 8SOIC |
| LT1372IS8#PBF | IC REG MULTI CONFIG ADJ 8SOIC |
| ABC05DRYI-S13 | CONN EDGECARD 10POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3602EUF#PBF | 功能描述:IC REG BUCK SYNC ADJ 2.5A 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3602EUF#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 2.5A 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3602IFE#PBF | 功能描述:IC REG BUCK SYNC ADJ 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3602IFE#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3602IUF#PBF | 功能描述:IC REG BUCK SYNC ADJ 2.5A 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。