- 您现在的位置：买卖IC网 > PDF目录13808 > LTC3609IWKG#PBF (Linear Technology)IC REG BUCK SYNC ADJ 6A 52QFN PDF资料下载
参数资料
| 型号： | LTC3609IWKG#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 14/26页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 6A 52QFN |
| 标准包装： | 45 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 36 V |
| 输入电压： | 4 V ~ 32 V |
| PWM 型： | 电流模式 |
| 电流 - 输出： | 6A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 52-VFQFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 52-QFN（7x8）裸露焊盘 |
LTC3609
APPLICATIONS INFORMATION
V OUT V IN
1
Δ V OUT ≤ Δ I L ? ESR + ?
OncethevalueforLisknown,thetypeofinductormust
be selected. High efficiency converters generally cannot
afford the core loss found in low cost powdered iron cores.
A variety of inductors designed for high current, low volt-
age applications are available from manufacturers such as
Sumida, Panasonic, Coiltronics, Coilcraft and Toko.
C IN and C OUT Selection
The input capacitance, C IN , is required to filter the square
wave current at the drain of the top MOSFET. Use a low ESR
capacitor sized to handle the maximum RMS current.
I RMS ? I OUT ( MAX ) –1
V IN V OUT
This formula has a maximum at V IN = 2V OUT , where
I RMS = I OUT(MAX) /2. This simple worst-case condition is
commonly used for design because even significant de-
viations do not offer much relief. Note that ripple current
ratings from capacitor manufacturers are often based on
only 2000 hours of life which makes it advisable to derate
the capacitor.
The selection of C OUT is primarily determined by the
ESR required to minimize voltage ripple and load step
transients. The output ripple ?V OUT is approximately
bounded by:
? ?
? 8fC OUT ?
Since ?I L increases with input voltage, the output ripple
is highest at maximum input voltage. Typically, once the
ESR requirement is satisfied, the capacitance is adequate
for filtering and has the necessary RMS current rating.
Multiple capacitors placed in parallel may be needed to
meet the ESR and RMS current handling requirements.
Dry tantalum, special polymer, aluminum electrolytic and
ceramic capacitors are all available in surface mount pack-
ages. Special polymer capacitors offer very low ESR but
have lower capacitance density than other types. Tantalum
capacitors have the highest capacitance density but it is
important to only use types that have been surge tested
for use in switching power supplies. Aluminum electrolytic
capacitors have significantly higher ESR, but can be used
in cost-sensitive applications providing that consideration
is given to ripple current ratings and long-term reliability.
Ceramic capacitors have excellent low ESR characteris-
tics but can have a high voltage coefficient and audible
piezoelectric effects. The high Q of ceramic capacitors with
trace inductance can also lead to significant ringing. When
used as input capacitors, care must be taken to ensure
that ringing from inrush currents and switching does not
pose an overvoltage hazard to the power switches and
controller. To dampen input voltage transients, add a small
5μF to 50μF aluminum electrolytic capacitor with an ESR in
the range of 0.5Ω to 2Ω. High performance through-hole
capacitors may also be used, but an additional ceramic
capacitor in parallel is recommended to reduce the effect
of their lead inductance.
Top MOSFET Driver Supply (C B , D B )
An external bootstrap capacitor, C B , connected to the BOOST
pin supplies the gate drive voltage for the topside MOSFET.
This capacitor is charged through diode D B from INTV CC
when the switch node is low. When the top MOSFET turns
on, the switch node rises to V IN and the BOOST pin rises
to approximately V IN + INTV CC . The boost capacitor needs
to store about 100 times the gate charge required by the
top MOSFET. In most applications an 0.1μF to 0.47μF, X5R
or X7R dielectric capacitor is adequate.
Discontinuous Mode Operation and FCB Pin
The FCB pin determines whether the bottom MOSFET
remains on when current reverses in the inductor. Tying
this pin above its 0.6V threshold enables discontinuous
operation where the bottom MOSFET turns off when in-
ductor current reverses. The load current at which current
reverses and discontinuous operation begins depends on
the amplitude of the inductor ripple current and will vary
3609fb
相关PDF资料 |
PDF描述 |
|---|---|
| LT3511MPMS#TRPBF | IC REG FLYBK ISO ADJ .24A 16MSOP |
| V72B3V3C100BG2 | CONVERTER MOD DC/DC 3.3V 100W |
| GMA15DTAD | CONN EDGECARD 30POS R/A .125 SLD |
| AS1330-BTDT-AD | IC REG BST SYNC ADJ 0.15A 8TDFN |
| MAX6721AUTZGD1+T | IC SUPERVISOR MPU SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3610EWP#PBF | 功能描述:IC REG BUCK SYNC ADJ 12A 64QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3610EWP#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 12A 64QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3610EWPPBF | 制造商:Linear Technology 功能描述:12A 24V Synch Step Down Reg LTC3610 |
| LTC3610IWP#PBF | 功能描述:IC REG BUCK SYNC ADJ 12A 64QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3610IWP#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 12A 64QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。