- 您现在的位置：买卖IC网 > PDF目录13808 > LTC3609IWKG#PBF (Linear Technology)IC REG BUCK SYNC ADJ 6A 52QFN PDF资料下载
参数资料
| 型号： | LTC3609IWKG#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 16/26页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 6A 52QFN |
| 标准包装： | 45 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 36 V |
| 输入电压： | 4 V ~ 32 V |
| PWM 型： | 电流模式 |
| 电流 - 输出： | 6A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 52-VFQFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 52-QFN（7x8）裸露焊盘 |
LTC3609
APPLICATIONS INFORMATION
( )
t DELAY =
C SS = 1 . 3 s / μ F C SS
TheEXTV CC pincanbeusedtoprovideMOSFETgatedrive
and control power from the output or another external
source during normal operation. Whenever the EXTV CC
pin is above 4.7V the internal 5V regulator is shut off and
an internal 50mA P-channel switch connects the EXTV CC
pin to INTV CC . INTV CC power is supplied from EXTV CC
until this pin drops below 4.5V. Do not apply more than
7V to the EXTV CC pin and ensure that EXTV CC ≤ V IN . The
following list summarizes the possible connections for
EXTV CC :
1. EXTV CC grounded. INTV CC is always powered from the
internal 5V regulator.
2. EXTV CC connected to an external supply. A high efficiency
supply compatible with the MOSFET gate drive require-
ments (typically 5V) can improve overall efficiency.
3. EXTV CC connected to an output derived boost network.
The low voltage output can be boosted using a charge
pump or flyback winding to greater than 4.7V. The system
will start-up using the internal linear regulator until the
boosted output supply is available.
Soft-Start and Latchoff with the RUN/SS Pin
The RUN/SS pin provides a means to shut down the LTC3609
as well as a timer for soft-start and overcurrent latchoff.
Pulling the RUN/SS pin below 0.8V puts the LTC3609 into
a low quiescent current shutdown (I Q < 30μA). Releasing
the pin allows an internal 1.2μA current source to charge
up the external timing capacitor, C SS . If RUN/SS has been
pulled all the way to ground, there is a delay before start-
ing of about:
1 . 5 V
1 . 2 μ A
When the voltage on RUN/SS reaches 1.5V, the LTC3609
begins operating with a clamp on I TH of approximately
0.9V. As the RUN/SS voltage rises to 3V, the clamp on I TH
is raised until its full 2.4V range is available. This takes an
additional 1.3s/μF, during which the load current is folded
back until the output reaches 75% of its final value.
After the controller has been started and given adequate
time to charge up the output capacitor, C SS is used as a
short-circuit timer. After the RUN/SS pin charges above 4V,
if the output voltage falls below 75% of its regulated value,
then a short-circuit fault is assumed. A 1.8μA current then
begins discharging C SS . If the fault condition persists until
the RUN/SS pin drops to 3.5V, then the controller turns
off both power MOSFETs, shutting down the converter
permanently. The RUN/SS pin must be actively pulled
down to ground in order to restart operation.
The overcurrent protection timer requires that the soft-start
timing capacitor, C SS , be made large enough to guarantee
that the output is in regulation by the time C SS has reached
the 4V threshold. In general, this will depend upon the
size of the output capacitance, output voltage and load
current characteristic. A minimum soft-start capacitor
can be estimated from:
C SS > C OUT V OUT R SENSE (10 –4 [F/V s])
Generally 0.1μF is more than sufficient.
Overcurrent latchoff operation is not always needed or
desired. Load current is already limited during a short
circuit by the current foldback circuitry and latchoff op-
eration can prove annoying during troubleshooting. The
feature can be overridden by adding a pull-up current
greater than 5μA to the RUN/SS pin. The additional cur-
rent prevents the discharge of C SS during a fault and also
shortens the soft-start period. Using a resistor to V IN as
shown in Figure 5a is simple, but slightly increases shut-
down current. Connecting a resistor to INTV CC as shown
in Figure 5b eliminates the additional shutdown current,
but requires a diode to isolate C SS . Any pull-up network
must be able to pull RUN/SS above the 4.2V maximum
threshold of the latchoff circuit and overcome the 4μA
maximum discharge current.
3609fb
相关PDF资料 |
PDF描述 |
|---|---|
| LT3511MPMS#TRPBF | IC REG FLYBK ISO ADJ .24A 16MSOP |
| V72B3V3C100BG2 | CONVERTER MOD DC/DC 3.3V 100W |
| GMA15DTAD | CONN EDGECARD 30POS R/A .125 SLD |
| AS1330-BTDT-AD | IC REG BST SYNC ADJ 0.15A 8TDFN |
| MAX6721AUTZGD1+T | IC SUPERVISOR MPU SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3610EWP#PBF | 功能描述:IC REG BUCK SYNC ADJ 12A 64QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3610EWP#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 12A 64QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3610EWPPBF | 制造商:Linear Technology 功能描述:12A 24V Synch Step Down Reg LTC3610 |
| LTC3610IWP#PBF | 功能描述:IC REG BUCK SYNC ADJ 12A 64QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3610IWP#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 12A 64QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。