- 您现在的位置：买卖IC网 > PDF目录30770 > LTC3615EFE-1#TRPBF (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, PDSO24 PDF资料下载
参数资料
| 型号： | LTC3615EFE-1#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, PDSO24 |
| 封装： | 4.40 MM, LEAD FREE, PLASTIC, TSSOP-24 |
| 文件页数： | 10/32页 |
| 文件大小： | 585K |
| 代理商： | LTC3615EFE-1#TRPBF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC3615/LTC3615-1
18
3615fa
Output Capacitor COUT Selection
The selection of COUT is typically driven by the required
ESR to minimize voltage ripple and load step transients
(low-ESR ceramic capacitors are discussed in the next
section). Typically, once the ESR requirement is satised,
the capacitance is adequate for ltering. The output ripple
ΔVOUT is determined by:
ΔΔ
VI
ESR
fC
OUT
L
SW
OUT
≤
+
1
8
where fSW=operatingfrequency,COUT=outputcapacitance
and ΔIL = ripple current in the inductor. The output ripple
is highest at maximum input voltage since ΔIL increases
with input voltage.
In surface mount applications, multiple capacitors may
have to be paralleled to meet the capacitance, ESR or RMS
current handling requirement of the application. Aluminum
electrolytic, special polymer, ceramic and dry tantalum
capacitors are all available in surface mount packages.
Tantalum capacitors have the highest capacitance density,
but can have higher ESR and must be surge tested for
use in switching power supplies. Aluminum electrolytic
capacitors have signicantly higher ESR, but can often
be used in extremely cost-sensitive applications provided
that consideration is given to ripple current ratings and
long term reliability.
Ceramic Input and Output Capacitors
Ceramic capacitors have the lowest ESR and can be cost
effective, but also have the lowest capacitance density,
high voltage and temperature coefcients, and exhibit
audible piezoelectric effects. In addition, the high-Q of
ceramic capacitors along with trace inductance can lead
to signicant ringing.
Capacitors are tempting for switching regulator use
because of their very low ESR. Great care must be taken
when using only ceramic input and output capacitors.
Ceramic caps are prone to temperature effects which re-
quire the designer to check loop stability over the operating
temperature range. To minimize their large temperature and
voltage coefcients, only X5R or X7R ceramic capacitors
should be used.
When a ceramic capacitor is used at the input, and the
power is being supplied through long wires, such as from
a wall adapter, a load step at the output can induce ringing
at the VIN pin. At best, this ringing can couple to the output
and be mistaken as loop instability. At worst, the ringing
at the input can be large enough to damage the part.
Since the ESR of a ceramic capacitor is so low, the input
and output capacitor must instead fulll a charge storage
requirement. During a load step, the output capacitor must
instantaneously supply the current to support the load
until the feedback loop raises the switch current enough
to support the load. The time required for the feedback
loop to respond is dependent on the compensation com-
ponents and the output capacitor size. Typically, three to
four cycles are required to respond to a load step, but only
in the rst cycle does the output drop linearly. The output
droop, VDROOP, is usually about two to three times the
linear drop of the rst cycle. Thus, a good place to start
is with the output capacitor size of approximately:
C
I
fV
OUT
SW
DROOP
≈
25
.
Δ
More capacitance may be required depending on the duty
cycle and load step requirements. In most applications,
the input capacitor is merely required to supply high
frequency bypassing, since the impedance to the supply
is very low.
APPLICATIONS INFORMATION
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3615IUF-1#PBF | SWITCHING REGULATOR, PQCC24 |
| LTC3615EUF#PBF | SWITCHING REGULATOR, PQCC24 |
| LTC3615EFE#PBF | SWITCHING REGULATOR, PDSO24 |
| LTC3615IFE-1#PBF | SWITCHING REGULATOR, PDSO24 |
| LTC3615EUF#TRPBF | SWITCHING REGULATOR, PQCC24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3615EUF#PBF | 功能描述:IC REG BUCK SYNC ADJ 3A DL 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3615EUF#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 3A DL 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3615EUF-1#PBF | 功能描述:IC REG BUCK SYNC ADJ 3A DL 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3615EUF-1#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 3A DL 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3615EUFPBF | 制造商:Linear Technology 功能描述:Dual 4MHz 3A Synch Step-Down DC/DC QFN24 |
发布紧急采购，3分钟左右您将得到回复。