- 您现在的位置：买卖IC网 > PDF目录13914 > LTC3616EUDD#TRPBF (Linear Technology)IC REG BUCK SYNC ADJ 6A 24QFN PDF资料下载
参数资料
| 型号： | LTC3616EUDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 22/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 6A 24QFN |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 5.5 V |
| 输入电压： | 2.25 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 300kHz ~ 4MHz |
| 电流 - 输出： | 6A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 24-QFN 裸露焊盘（3x5） |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页
LTC3616
APPLICATIONS INFORMATION
Although all dissipative elements in the circuit produce
losses, two main sources usually account for most of
the losses: V IN quiescent current and I 2 R losses. The V IN
quiescent current loss dominates the efficiency loss at
very low load currents whereas the I 2 R loss dominates
the efficiency loss at medium to high load currents. In a
typical efficiency plot, the efficiency curve at very low load
currents can be misleading since the actual power lost is
usually of no consequence.
1. The V IN quiescent current is due to two components: the
DC bias current as given in the Electrical Characteristics
and the internal main switch and synchronous switch
gate charge currents. The gate charge current results
from switching the gate capacitance of the internal power
MOSFET switches. Each time the gate is switched from
low to high to low again, a packet of charge dQ moves
from V IN to ground. The resulting dQ/dt is the current
out of V IN due to gate charge, and it is typically larger
than the DC bias current. Both the DC bias and gate
charge losses are proportional to V IN ; thus, their effects
will be more pronounced at higher supply voltages.
2. I 2 R losses are calculated from the resistances of the
internal switches, R SW , and external inductor, R L . In
continuous mode the average output current flowing
through inductor L is “chopped” between the main
switch and the synchronous switch. Thus, the series
resistance looking into the SW pin is a function of both
top and bottom MOSFET R DS(ON) and the duty cycle
(DC) as follows:
R SW = (R DS(ON)TOP )(DC) + (R DS(ON)BOT )(1 – DC)
The R DS(ON) for both the top and bottom MOSFETs can
be obtained from the Typical Performance Character-
istics curves. To obtain I 2 R losses, simply add R SW to
R L and multiply the result by the square of the average
output current.
Other losses including C IN and C OUT ESR dissipative
losses and inductor core losses generally account for
less than 2% of the total loss.
Thermal Considerations
In most applications, the LTC3616 does not dissipate
much heat due to its high efficiency.
However, in applications where the LTC3616 is running
at high ambient temperature with low supply voltage and
high duty cycles, such as in dropout, the heat dissipated
may exceed the maximum junction temperature of the part.
If the junction temperature reaches approximately 170°C,
both power switches will be turned off and the SW node
will become high impedance.
To prevent the LTC3616 from exceeding the maximum
junction temperature, some thermal analysis is required.
The temperature rise is given by:
T RISE = (P D )( θ JA )
where P D is the power dissipated by the regulator and
θ JA is the thermal resistance from the junction of the die
to the ambient temperature. The junction temperature,
T J , is given by:
T J = T A + T RISE
where T A is the ambient temperature.
As an example, consider the case when the LTC3616 is in
dropout at an input voltage of 3.3V with a load current of
6A at an ambient temperature of 70°C. From the Typical
Performance Characteristics graph of Switch Resistance,
the R DS(ON) resistance of the P-channel switch is 0.035Ω.
Therefore, power dissipated by the part is:
P D = (I OUT ) 2 ? R DS(ON) = 1.26W
For the QFN package, the θ JA is 38°C/W.
Therefore, the junction temperature of the regulator op-
erating at 70°C ambient temperature is approximately:
T J = 1.26W ? 38° C/W + 70°C = 118°C
We can safely assume that the actual junction temperature
will not exceed the absolute maximum junction tempera-
ture of 125°C.
Note that for very low input voltage, the junction tempera-
ture will be higher due to increased switch resistance,
R DS(ON) . It is not recommended to use full load current
for high ambient temperature and low input voltage.
To maximize the thermal performance of the LTC3616 the
exposed pad should be soldered to a ground plane. See
the PCB Layout Board Checklist.
22
For more information www.linear.com/LTC3616
3616fb
相关PDF资料 |
PDF描述 |
|---|---|
| V300B5C150BF3 | CONVERTER MOD DC/DC 5V 150W |
| LTC3412EFE | IC REG BUCK SYNC ADJ 16TSSOP |
| EBM36DCBN-S189 | CONN EDGECARD 72POS R/A .156 SLD |
| LTC1434IGN#TRPBF | IC REG BUCK 3.3V/5V/ADJ 20SSOP |
| V300B5C150BF2 | CONVERTER MOD DC/DC 5V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3616HUDD#PBF | 制造商:Linear Technology 功能描述:IC REG BUCK SYNC ADJ 6A 24QFN |
| LTC3616IUDD#PBF | 功能描述:IC REG BUCK SYNC ADJ 6A 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3616IUDD#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 6A 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3616MPUDD#PBF | 制造商:Linear Technology 功能描述:IC REG BUCK SYNC ADJ 6A 24QFN |
| LTC3616MPUDD#TRPBF | 制造商:Linear Technology 功能描述:IC REG BUCK SYNC ADJ 6A 24QFN |
发布紧急采购，3分钟左右您将得到回复。