- 您现在的位置：买卖IC网 > PDF目录13914 > LTC3616EUDD#TRPBF (Linear Technology)IC REG BUCK SYNC ADJ 6A 24QFN PDF资料下载
参数资料
| 型号： | LTC3616EUDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 6A 24QFN |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 5.5 V |
| 输入电压： | 2.25 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 300kHz ~ 4MHz |
| 电流 - 输出： | 6A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 24-QFN 裸露焊盘（3x5） |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC3616
PIN FUNCTIONS
SRLIM/DDR (Pin 1): Slew Rate Limit. Tying this pin to
ground selects maximum slew rate. Minimum slew rate
is selected when the pin is open. Connecting a resistor
from SRLIM/DDR to ground allows the slew rate to be
continuously adjusted. If SRLIM/DDR is tied to S VIN , DDR
mode is selected. In DDR mode the slew rate limit is set
to maximum.
RT/SYNC (Pin 2): Oscillator Frequency. This pin provides
three ways of setting the constant switching frequency:
1. Connecting a resistor from RT/SYNC to ground will set
the switching frequency based on the resistor value.
2. Driving the RT/SYNC pin with an external clock signal
will synchronize the LTC3616 to the applied frequency.
The slope compensation is automatically adapted to the
external clock frequency.
3. Tying the RT/SYNC pin to SV IN enables the internal
2.25MHz oscillator frequency.
SGND (Pin 3): Signal Ground. All small-signal and com-
pensation components should connect to this ground,
which in turn should connect to PGND at a single point.
PV IN (Pins 4, 10, 11, 17): Power Input Supply. PV IN
connects to the source of the internal P-channel power
MOSFET. This pin is independent of SV IN and may be con-
nected to the same voltage or to a lower voltage supply.
SW (Pins 5, 6, 7, 8, 13, 14, 15, 16): Switch Node. Con-
nection to the inductor. These pins connect to the drains
of the internal synchronous power MOSFET switches.
NC (Pins 9, 12): Can be connected to ground or left open.
SV IN (Pin 18): Signal Input Supply. This pin powers the
internal control circuitry and is monitored by the under-
voltage lockout comparator.
RUN (Pin 19): Enable Pin. Forcing this pin to ground shuts
down the LTC3616. In shutdown, all functions are disabled
and the chip draws <1μA of supply current.
PGOOD (Pin 20): Power Good. This open-drain output is
pulled down to SGND on start-up and while the FB voltage
is outside the power good voltage window. If the FB volt-
age increases and stays inside the power good window
for more than 100μs the PGOOD pin is released. If the
FB voltage leaves the power good window for more than
100μs the PGOOD pin is pulled down.
In DDR mode (DDR = V IN ), the power good window moves
in relation to the actual TRACK/SS pin voltage. During
up/down tracking the PGOOD pin is always pulled down.
In shutdown the PGOOD output will actively pull down
and may be used to discharge the output capacitors via
an external resistor.
MODE (Pin 21): Mode Selection. Tying the MODE pin
to SV IN or SGND enables pulse-skipping mode or Burst
Mode operation (with an internal Burst Mode clamp),
respectively. If this pin is held at slightly higher than half
of SV IN , forced continuous mode is selected. Connecting
this pin to an external voltage selects Burst Mode opera-
tion with the burst clamp set to the pin voltage. See the
Operation section for more details.
V FB (Pin 22): Voltage Feedback Input Pin. Senses the
feedback voltage from the external resistive divider across
the output.
ITH (Pin 23): Error Amplifier Compensation. The current
comparator’s threshold increases with this control volt-
age. Tying this pin to SV IN enables internal compensation
and AVP mode.
TRACK/SS (Pin 24): Track/External Soft-Start/External
Reference. Start-up behavior is programmable with the
TRACK/SS pin:
1. Tying this pin to SV IN selects the internal soft-start
circuit.
2. External soft-start timing can be programmed with a
capacitor to ground and a resistor to SV IN .
3. TRACK/SS can be used to force the LTC3616 to track
the start-up behavior of another supply.
The pin can also be used as external reference input. See
the Applications Information section for more information.
PGND (Exposed Pad Pin 25): Power Ground. This pin
connects to the source of the internal N-channel power
MOSFET. This pin should be connected close to the (–)
terminal of C IN and C OUT .
9
For more information www.linear.com/LTC3616
3616fb
相关PDF资料 |
PDF描述 |
|---|---|
| V300B5C150BF3 | CONVERTER MOD DC/DC 5V 150W |
| LTC3412EFE | IC REG BUCK SYNC ADJ 16TSSOP |
| EBM36DCBN-S189 | CONN EDGECARD 72POS R/A .156 SLD |
| LTC1434IGN#TRPBF | IC REG BUCK 3.3V/5V/ADJ 20SSOP |
| V300B5C150BF2 | CONVERTER MOD DC/DC 5V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3616HUDD#PBF | 制造商:Linear Technology 功能描述:IC REG BUCK SYNC ADJ 6A 24QFN |
| LTC3616IUDD#PBF | 功能描述:IC REG BUCK SYNC ADJ 6A 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3616IUDD#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 6A 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3616MPUDD#PBF | 制造商:Linear Technology 功能描述:IC REG BUCK SYNC ADJ 6A 24QFN |
| LTC3616MPUDD#TRPBF | 制造商:Linear Technology 功能描述:IC REG BUCK SYNC ADJ 6A 24QFN |
发布紧急采购，3分钟左右您将得到回复。