- 您现在的位置：买卖IC网 > PDF目录13882 > LTC3633EUFD#TRPBF (Linear Technology)IC REG BUCK ADJ 3A DL 28QFN PDF资料下载
参数资料
| 型号： | LTC3633EUFD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 16/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 3A DL 28QFN |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 0.6 V ~ 14.7 V |
| 输入电压： | 3.6 V ~ 15 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 500kHz ~ 4MHz |
| 电流 - 输出： | 3A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 28-QFN（4x5） |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC3633
APPLICATIONS INFORMATION
LTC3633
Suggested compensation component values are shown in
Figure 3. For a 2MHz application, an R-C network of 220pF
and 13kΩ provides a good starting point. The bandwidth
of the loop increases with decreasing C. If R is increased
by the same factor that C is decreased, the zero frequency
will be kept the same, thereby keeping the phase the same
in the most critical frequency range of the feedback loop.
A 10pF bypass capacitor on the ITH pin is recommended
for the purposes of filtering out high frequency coupling
from stray board capacitance. In addition, a feedforward
capacitor C F can be added to improve the high frequency
response, as previously shown in Figure 2. Capacitor C F
provides phase lead by creating a high frequency zero
with R2 which improves the phase margin.
ITH
R COMP
13k
C COMP
220pF
SGND
3633 F03
Figure 3. Compensation Component
Checking Transient Response
The regulator loop response can be checked by observing
the response of the system to a load step. When configured
for external compensation, the availability of the ITH pin
not only allows optimization of the control loop behavior
but also provides a DC-coupled and AC filtered closed loop
response test point. The DC step, rise time, and settling
behavior at this test point reflect the closed loop response.
Assuming a predominantly second order system, phase
margin and/or damping factor can be estimated using the
percentage of overshoot seen at this pin.
The ITH external components shown in Figure 3 circuit
will provide an adequate starting point for most applica-
tions. The series R-C filter sets the dominant pole-zero
loop compensation. The values can be modified slightly
(from 0.5 to 2 times their suggested values) to optimize
transient response once the final PC layout is done and
the particular output capacitor type and value have been
determined. The output capacitors need to be selected
because their various types and values determine the
loop gain and phase. An output current pulse of 20% to
100% of full load current having a rise time of ~1μs will
produce output voltage and ITH pin waveforms that will
give a sense of the overall loop stability without breaking
the feedback loop.
Switching regulators take several cycles to respond to a
step in load current. When a load step occurs, V OUT im-
mediately shifts by an amount equal to ?I LOAD ? ESR, where
ESR is the effective series resistance of C OUT . ?I LOAD also
begins to charge or discharge C OUT generating a feedback
error signal used by the regulator to return V OUT to its
steady-state value. During this recovery time, V OUT can
be monitored for overshoot or ringing that would indicate
a stability problem.
When observing the response of V OUT to a load step, the
initial output voltage step may not be within the bandwidth of
the feedback loop, so the standard second order overshoot/
DC ratio cannot be used to determine phase margin. The
output voltage settling behavior is related to the stability
of the closed-loop system and will demonstrate the actual
overall supply performance. For a detailed explanation of
optimizing the compensation components, including a
review of control loop theory, refer to Linear Technology
Application Note 76.
In some applications, a more severe transient can be caused
by switching in loads with large (>10μF) input capacitors.
The discharged input capacitors are effectively put in paral-
lel with C OUT , causing a rapid drop in V OUT . No regulator
can deliver enough current to prevent this problem, if
the switch connecting the load has low resistance and is
driven quickly. The solution is to limit the turn-on speed
of the load switch driver. A hot swap controller is designed
specifically for this purpose and usually incorporates cur-
rent limiting, short-circuit protection, and soft starting.
3633fc
16
For more information www.linear.com/LTC3633
相关PDF资料 |
PDF描述 |
|---|---|
| ECA35DTAH | CONN EDGECARD 70POS R/A .125 SLD |
| FSM08DSEN | CONN EDGECARD 16POS .156 EYELET |
| VI-J3D-EY-S | CONVERTER MOD DC/DC 85V 50W |
| ECA35DTAD | CONN EDGECARD 70POS R/A .125 SLD |
| 16ZL120MEFC8X7 | CAP ALUM 120UF 16V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3633IFE#PBF | 功能描述:IC REG BUCK ADJ 3A DL 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3633IFE#TRPBF | 功能描述:IC REG BUCK ADJ 3A DL 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3633IUFD#PBF | 功能描述:IC REG BUCK ADJ 3A DL 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:MIC23xxx HyperLight Load™ Regulators 标准包装:5,000 系列:HyperLight Load® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.8V 输入电压:2.7 V ~ 5.5 V PWM 型:混合物 频率 - 开关:4MHz 电流 - 输出:2A 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 包装:带卷 (TR) 供应商设备封装:8-MLF?（2x2） 产品目录页面:1094 (CN2011-ZH PDF) 其它名称:576-3303-2 |
| LTC3633IUFD#TRPBF | 功能描述:IC REG BUCK ADJ 3A DL 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3633IUFDPBF | 制造商:Linear Technology 功能描述:Conv DC-DC Dual Step-Down 3.6-15V QFN28 |
发布紧急采购，3分钟左右您将得到回复。