- 您现在的位置：买卖IC网 > PDF目录15314 > LTC3703EGN#TR (Linear Technology)IC REG CTRLR BST PWM VM 16-SSOP PDF资料下载
参数资料
| 型号： | LTC3703EGN#TR |
| 厂商： | Linear Technology |
| 文件页数： | 13/34页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST PWM VM 16-SSOP |
| 标准包装： | 2,500 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 330kHz |
| 占空比： | 96% |
| 电源电压： | 9.3 V ~ 15 V |
| 降压： | 是 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
LTC3703
APPLICATIONS INFORMATION
V OUT ?
V OUT
?
?
V OUT ? V OUT ?
? ? 1– V
? I L = ?
The oscillator can also be synchronized to an external
clock applied to the MODE/SYNC pin with a frequency in
the range of 100kHz to 600kHz (refer to the MODE/SYNC
Pin section for more details). In this synchronized mode,
pulse-skip mode operation is disabled. The clock high level
must exceed 2V for at least 25ns. As shown in Figure 8,
the top MOSFET turn-on will follow the rising edge of the
external clock by a constant delay equal to one-tenth of
the cycle period.
2V TO 10V
MODE/
SYNC
t MIN = 25ns
0.8T T T = 1/f O
TG D = 40%
0.1T
I L
3703 F08
Figure 8. MODE/SYNC Clock Input and Switching
Waveforms for Synchronous Operation
Inductor
The inductor in a typical LTC3703 circuit is chosen for a
specific ripple current and saturation current. Given an
input voltage range and an output voltage, the inductor
value and operating frequency directly determine the ripple
current. The inductor ripple current in the buck mode is:
(f)(L) IN ?
Lower ripple current reduces core losses in the inductor,
ESR losses in the output capacitors and output voltage
ripple. Thus highest efficiency operation is obtained at
low frequency with small ripple current. To achieve this
however, requires a large inductor.
A reasonable starting point is to choose a ripple current
between 20% and 40% of I O(MAX) . Note that the largest
ripple current occurs at the highest V IN . To guarantee that
ripple current does not exceed a specified maximum, the
inductor in buck mode should be chosen according to:
?
L ≥ 1–
f ? I L(MAX) ? V IN(MAX) ?
The inductor also has an affect on low current operation
when pulse-skip mode operation is enabled. The frequency
begins to decrease when the output current drops below
the average inductor current at which the LTC3703 is
operating at its t ON(MIN) in discontinuous mode (see
Figure 6). Lower inductance increases the peak inductor
current that occurs in each minimum on-time pulse and
thus increases the output current at which the frequency
starts decreasing.
Power MOSFET Selection
The LTC3703 requires at least two external N-channel
power MOSFETs, one for the top (main) switch and one or
more for the bottom (synchronous) switch. The number,
type and “on” resistance of all MOSFETs selected take into
account the voltage step-down ratio as well as the actual
position (main or synchronous) in which the MOSFET will
be used. A much smaller and much lower input capacitance
MOSFET should be used for the top MOSFET in applica-
tions that have an output voltage that is less than 1/3 of
the input voltage. In applications where V IN >> V OUT , the
top MOSFETs’ “on” resistance is normally less important
for overall efficiency than its input capacitance at operating
frequencies above 300kHz. MOSFET manufacturers have
designed special purpose devices that provide reason-
ably low “on” resistance with significantly reduced input
capacitance for the main switch application in switching
regulators.
Selection criteria for the power MOSFETs include the “on”
resistance R DS(ON) , input capacitance, breakdown voltage
and maximum output current.
The most important parameter in high voltage applications
is breakdown voltage BV DSS . Both the top and bottom
MOSFETs will see full input voltage plus any additional
ringing on the switch node across its drain-to-source dur-
ing its off-time and must be chosen with the appropriate
3703fc
13
相关PDF资料 |
PDF描述 |
|---|---|
| VI-220-EY-B1 | CONVERTER MOD DC/DC 5V 50W |
| CDRH4D28NP-1R8NC | INDUCTOR POWER 1.8UH 2.20A SMD |
| EEC31DRAI-S734 | CONN EDGECARD 62POS .100 R/A PCB |
| LTC1735CS-1#PBF | IC REG CTRLR BUCK PWM CM 16-SOIC |
| ESA22DRMN-S288 | CONN EDGECARD 44POS .125 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3703EGPBF | 制造商:Linear Technology 功能描述:LTC3703 100V SU/SD PS controller |
| LTC3703HGN | 制造商:Linear Technology 功能描述:DC DC Cntrlr Single-OUT Sync Step Down 9.3V to 100V Input 16-Pin SSOP N |
| LTC3703HGN#PBF | 功能描述:IC REG CTRLR BST PWM VM 16-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3703HGN#TRPBF | 功能描述:IC REG CTRLR BST PWM VM 16-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3703IG-5#PBF | 功能描述:IC REG CTRLR BST PWM VM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。