- 您现在的位置：买卖IC网 > PDF目录15237 > LTC3703IGN-5#PBF (Linear Technology)IC REG CTRLR BST PWM VM 16-SSOP PDF资料下载
参数资料
| 型号： | LTC3703IGN-5#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 28/32页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST PWM VM 16-SSOP |
| 标准包装： | 100 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 330kHz |
| 占空比： | 96% |
| 电源电压： | 4.1 V ~ 15 V |
| 降压： | 是 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页
LTC3703-5
APPLICATIO S I FOR ATIO
estimated at maximum input voltage, assuming a junction
temperature of 100 ° C (30 ° C above an ambient of 70 ° C):
However, a 0A to 10A load step will cause an output
voltage change of up to:
P MAIN =
12
60
( 10 ) 2 [ 1 + 0 . 007 ( 100 – 25 ) ] ( 0 . 022 )
? V OUT(STEP) = ? I LOAD(ESR) = (10A)(0.009 ? )
= 90mV
+ ( 60 ) 2 ?
? ( 2 )( 200 pF ) ? ?
? ( 250 k )
? 10 ? ? 1
? 2 ? ? 10 – 3 . 8
= 0 . 67 W + 0 . 76 W = 1 . 43 W
+
1 ?
3 . 8 ?
PC Board Layout Checklist
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of the
? ( 10 ) 2 [ 1 + 0 . 007 ( 100 – 25 ) ] ?
P SYNC = ?
? = 1 . 34 W
?
And double check the assumed T J in the MOSFET:
T J = 70 ° C + (1.43W)(20 ° C/W) = 99 ° C
Since the synchronous MOSFET will be conducting over
twice as long each period (almost 100% of the period in
short circuit) as the top MOSFET, use two Si7850DP
MOSFETs on the bottom:
? 60 ? 12 ?
? 60 ?
? 0 . 022 ?
? 2 ?
T J = 70 ° C + (1.34W)(20 ° C/W) = 97 ° C
Next, set the current limit resistor. Since I MAX = 10A, the
limit should be set such that the minimum current limit is
>10A. Minimum current limit occurs at maximum R DS(ON) .
Using the above calculation for bottom MOSFET T J , the
max R DS(ON) = (22m ? /2) [1 + 0.007 (97-25)] = 16.5m ?
Therefore, I MAX pin voltage should be set to (10A)(0.0165)
= 0.165V. The R SET resistor can now be chosen to be
0.165V/12 μ A = 14k ? .
C IN is chosen for an RMS current rating of about 5A
(I MAX /2) at 85 ° C. For the output capacitor, two low ESR
OS-CON capacitors (18m ? each) are used to minimize
output voltage changes due to inductor current ripple and
load steps. The ripple voltage will be:
? V OUT(RIPPLE) = ? I L(MAX) (ESR) = (4A)(0.018 ? /2)
LTC3703-5. These items are also illustrated graphically in
the layout diagram of Figure 20. For layout of a boost mode
converter, layout is similar with V IN and V OUT swapped.
Check the following in your layout:
1. Keep the signal and power grounds separate. The signal
ground consists of the LTC3703-5 GND pin, the ground
return of C VCC , and the (–) terminal of V OUT . The power
ground consists of the Schottky diode anode, the source
of the bottom side MOSFET, and the (–) terminal of the
input capacitor and DRV CC capacitor. Connect the signal
and power grounds together at the (–) terminal of the
output capacitor. Also, try to connect the (–) terminal of
the output capacitor as close as possible to the (–)
terminals of the input and DRV CC capacitor and away from
the Schottky loop described in (2).
2. The high di/dt loop formed by the top N-channel
MOSFET, the bottom MOSFET and the C IN capacitor
should have short leads and PC trace lengths to minimize
high frequency noise and voltage stress from inductive
ringing.
3. Connect the drain of the top side MOSFET directly to the
(+) plate of C IN , and connect the source of the bottom side
MOSFET directly to the (–) terminal of C IN . This capacitor
provides the AC current to the MOSFETs.
4. Place the ceramic C DRVCC decoupling capacitor imme-
diately next to the IC, between DRV CC and BGRTN. This
capacitor carries the MOSFET drivers’ current peaks.
Likewise the C B capacitor should also be next to the IC
between BOOST and SW.
= 36mV
37035fa
28
相关PDF资料 |
PDF描述 |
|---|---|
| LT3757MPMSE#TRPBF | IC REG CTRLR PWM CM 10-MSOP |
| NCP304HSQ30T1G | IC VOLT DETECT CMOS 3.0V SC-82AB |
| ISC1210EB150J | INDUCTOR WW 15UH 5% 1210 |
| LTC3890HUH#TRPBF | IC REG CTRLR BUCK PWM CM 32-QFN |
| LTC3722IGN-2#TRPBF | IC REG CTRLR DIV ISO PWM 24SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3703IGNPBF | 制造商:Linear Technology 功能描述:DC-DC Controller Step-Dn 9.3-100V SSOP16 |
| LTC3704EMS | 功能描述:IC REG CTRLR INV PWM CM 10-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3704EMS#PBF | 功能描述:IC REG CTRLR INV PWM CM 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LTC3704EMS#PBF | 制造商:Linear Technology 功能描述:IC, DC/DC CONTROLLER, 300kHz, MSOP-10 |
| LTC3704EMS#TR | 功能描述:IC REG CTRLR INV PWM CM 10-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。