- 您现在的位置：买卖IC网 > PDF目录15303 > LTC3778EF#TR (Linear Technology)IC REG CTRLR BUCK PWM CM 20TSSOP PDF资料下载
参数资料
| 型号： | LTC3778EF#TR |
| 厂商： | Linear Technology |
| 文件页数： | 7/24页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 20TSSOP |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 电源电压： | 4 V ~ 36 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 包装： | 带卷 (TR) |
| 其它名称： | LTC3778EFTR |
LTC3778
PI FU CTIO S
RUN/SS (Pin 1): Run Control and Soft-Start Input. A
capacitor to ground at this pin sets the ramp time to full
output current (approximately 3s/ μ F) and the time delay
for overcurrent latchoff (see Applications Information).
Forcing this pin below 0.8V shuts down the device.
V ON (Pin 2): On-Time Voltage Input. Voltage trip point for
the on-time comparator. Tying this pin to the output
voltage makes the on-time proportional to V OUT . The
comparator input defaults to 0.7V when the pin is grounded,
2.4V when the pin is tied to INTV CC .
PGOOD (Pin 3): Power Good Output. Open drain logic
output that is pulled to ground when the output voltage is
not within ± 10% of the regulation point.
V RNG (Pin 4): Sense Voltage Range Input. The voltage at
this pin is ten times the nominal sense voltage at maximum
output current and can be set from 0.5V to 2V by a resistive
divider from INTV CC . The nominal sense voltage defaults
to 70mV when this pin is tied to ground, 140mV when tied
to INTV CC .
I TH (Pin 5): Current Control Threshold and Error Amplifier
Compensation Point. The current comparator threshold
increases with this control voltage. The voltage ranges
from 0V to 2.4V with 0.8V corresponding to zero sense
voltage (zero current).
FCB (Pin 6): Forced Continuous Input. Tie this pin to
ground to force continuous synchronous operation at low
load, to INTV CC to enable discontinuous mode operation at
low load or to a resistive divider from a secondary output
when using a secondary winding.
SGND (Pin 7): Signal Ground. All small-signal compo-
nents and compensation components should connect to
this ground, which in turn connects to PGND at one point.
I ON (Pin 8): On-Time Current Input. Tie a resistor from V IN
to this pin to set the one-shot timer current and thereby set
the switching frequency.
V FB (Pin 9): Error Amplifier Feedback Input. This pin
connects the error amplifier input to an external resistive
divider from V OUT .
EXTV CC (Pin 10): External V CC Input. When EXTV CC ex-
and shuts down the internal regulator so that controller
power is drawn from EXTV CC . Do not exceed 7V at this pin
and ensure that EXTV CC < V IN .
V IN (Pin 11): Main Input Supply. Decouple this pin to
SGND with an RC filter (1 ? , 0.1 μ F).
INTV CC (Pin 12): Internal 5V Regulator Output. The inter-
nal control circuits are powered from this voltage. De-
couple this pin to power ground with a minimum of 1 μ F
low ESR tantalum or ceramic capacitor.
DRV CC (Pin 13): Voltage Supply to Bottom Gate Driver.
Normally connected to the INTV CC pin through a decoupling
RC filter (1 ? , 0.1 μ F). Decouple this pin to power ground
with a minimum of 4.7 μ F low ESR tantalum or ceramic
capacitor. Do not exceed 7V at this pin.
BG (Pin 14): Bottom Gate Drive. Drives the gate of the
bottom N-channel MOSFET between ground and DRV CC .
PGND (Pin 15): Power Ground. Connect this pin closely to
the source of the bottom N-channel MOSFET or to the
bottom of the sense resistor when used, the (–) terminal
of C VCC and the (–) terminal of C IN .
SENSE – (Pin 16): Current Sense Comparator Input. The
(–) input to the current comparator is used to accurately
Kelvin sense the bottom side of the sense resistor or
MOSFET.
SENSE + (Pin 17): Current Sense Comparator Input. The
(+) input to the current comparator is normally connected
to the SW node unless using a sense resistor (See Appli-
cations Information).
SW (Pin 18): Switch Node. The (–) terminal of the boot-
strap capacitor C B connects here. This pin swings from a
diode voltage drop below ground up to V IN .
TG (Pin 19): Top Gate Drive. Drives the top N-channel
MOSFET with a voltage swing equal to DRV CC superim-
posed on the switch node voltage SW.
BOOST (Pin 20): Boosted Floating Driver Supply. The (+)
terminal of the bootstrap capacitor C B connects here. This
pin swings from a diode voltage drop below DRV CC up to
V IN + DRV CC .
ceeds 4.7V, an internal switch connects this pin to INTV CC
3778f
7
相关PDF资料 |
PDF描述 |
|---|---|
| VE-JW4-EY-F4 | CONVERTER MOD DC/DC 48V 50W |
| VI-JWB-EW-F1 | CONVERTER MOD DC/DC 95V 100W |
| H2BXT-10112-B8-ND | JUMPER-H1500TR/A3048B/X 12" |
| ESC19DREI-S93 | CONN EDGECARD 38POS .100 EYELET |
| TVX2G4R7MCD | CAP ALUM 4.7UF 400V 20% AXIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3780EG | 制造商:Linear Technology 功能描述:DC DC Cntrlr Dual-OUT Synchronous Boost/Buck Controller 4V to 36V Input 24-Pin SSOP |
| LTC3780EG#PBF | 功能描述:IC REG CTRLR BST PWM CM 24-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LTC3780EG#TR | 制造商:Linear Technology 功能描述:DC DC Cntrlr Dual-OUT Synchronous Boost/Buck Controller 4V to 36V Input 24-Pin SSOP T/R |
| LTC3780EG#TRPBF | 功能描述:IC REG CTRLR BST PWM CM 24-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC3780EGPBF | 制造商:Linear Technology 功能描述:4-Switch Buck-Boost Controller SSOP24 |
发布紧急采购，3分钟左右您将得到回复。