参数资料
型号: LTC3802EGN#TR
厂商: Linear Technology
文件页数: 24/28页
文件大小: 0K
描述: IC REG CTRLR BUCK PWM VM 28-SSOP
标准包装: 2,500
系列: PolyPhase®
PWM 型: 电压模式
输出数: 2
频率 - 最大: 850kHz
占空比: 92%
电源电压: 3 V ~ 30 V
降压:
升压:
回扫:
反相:
倍增器:
除法器:
Cuk:
隔离:
工作温度: -40°C ~ 85°C
封装/外壳: 28-SSOP(0.154",3.90mm 宽)
包装: 带卷 (TR)
LTC3802
APPLICATIO S I FOR ATIO
Medium voltage (20V to 35V) ceramic, tantalum, OS-CON
and switcher-rated electrolytic capacitors can be used as
input capacitors, but each has drawbacks: ceramics have
high voltage coefficients of capacitance and may have
audible piezoelectric effects; tantalums need to be surge-
rated; OS-CONs suffer from higher inductance, larger case
size and limited surface mount applicability; and
electrolytics’ higher ESR and dryout possibility require
several to be used. Sanyo OS-CON SVP, SVPD series;
Sanyo POSCAP TQC series or aluminum electrolytic ca-
pacitors from Panasonic WA series or Cornel Dublilier
SPV series, in parallel with a couple of high performance
ceramic capacitors, can be used as an effective means of
achieving low ESR and its big bulk capacitance goal for the
input bypass.
C OUT Selection
The selection of C OUT is primarily determined by the ESR
required to minimize voltage ripple and load step tran-
sients. The output ripple ? V OUT is approximately bounded
by:
In surface mount applications, multiple capacitors may
have to be paralleled to meet the ESR or transient current
handling requirements of the application. Aluminum elec-
trolytic and dry tantalum capacitors are both available in
surface mount configurations. New special polymer sur-
face mount capacitors offer very low ESR also but have
much lower capacitive density per unit volume. In the case
of tantalum, it is critical that the capacitors are surge tested
for use in switching power supplies. Several excellent
output capacitor choices are the Sanyo POSCAP TPD,
POSCAP TPB, AVX TPS, AVX TPSV, the Kemet T510 series
of surface mount tantalums,Kemet AO-CAPs or the Pana-
sonic SP series of surface mount special polymer capaci-
tors available in case heights ranging from 2mm to 4mm.
Other capacitor types include Nichicon PL series and
Sprague 595D series. Consult the manufacturer for other
specific recommendations.
Inductor Selection
The inductor in a typical LTC3802 circuit is chosen prima-
rily for inductance value and saturation current. The induc-
? V OUT ≤ ? I L ? ESR +
8 ? f SW OUT ?
?
?
?
? C
1 ?
tor should not saturate below the hard current limit
threshold.
The inductor value sets the ripple current, which is
where ? I L is the inductor ripple current.
? I L may be calculated using the equation:
commonly chosen at around 40% of the anticipated full
load current. Lower ripple current reduces core losses in
the inductor, ESR losses in the output capacitors and
V OUT ?
L ? f SW ?
V OUT ?
V IN ?
? I L =
? 1 –
?
output voltage ripple. Highest efficiency is obtained at low
frequency with small ripple current. However, achieving
high efficiency requires a large inductor and generates
Since ? I L increases with input voltage, the output ripple
voltage is highest at maximum input voltage. Typically,
once the ESR requirement is satisfied, the capacitance is
adequate for filtering and has the necessary RMS current
rating.
higher output voltage excursion during load transients.
There is a tradeoff between component size, efficiency
and operating frequency. Given a specified limit for ripple
current, the inductor value can be obtained using the
following equation:
f SW ? ? I L ( MAX ) ?
Manufacturers  such  as  Sanyo,  Panasonic  and  Cornell
Dublilier should be considered for high performance
through-hole capacitors. The OS-CON semiconductor elec-
L =
V OUT ?
? ? 1 –
V OUT ?
V IN ( MAX ) ? ?
trolyte capacitor available from Sanyo has a good
(ESR)(size) product. An additional ceramic capacitor in
parallel with OS-CON capacitors is recommended to offset
the effect of lead inductance.
Once the value for L is known, the type of inductor must be
selected. High efficiency converters generally cannot
afford the core loss found in low cost powdered iron cores,
forcing the use of more expensive ferrite, molypermalloy
3802f
24
相关PDF资料
PDF描述
VI-J5K-EW-F4 CONVERTER MOD DC/DC 40V 100W
H2BXG-10108-L4-ND JUMPER-H1501TR/A2015L/X 8"
VI-J5K-EW-F3 CONVERTER MOD DC/DC 40V 100W
LTC3731HG#TRPBF IC REG CTRLR BUCK PWM CM 36-SSOP
VI-J5K-EW-F2 CONVERTER MOD DC/DC 40V 100W
相关代理商/技术参数
参数描述
LTC3802EUH 功能描述:IC REG CTRLR BUCK PWM VM 32-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LTC3802EUH#PBF 功能描述:IC REG CTRLR BUCK PWM VM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LTC3802EUH#TR 功能描述:IC REG CTRLR BUCK PWM VM 32-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LTC3802EUH#TRPBF 功能描述:IC REG CTRLR BUCK PWM VM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LTC3803ES6 制造商:Linear Technology 功能描述:DC DC Cntrlr Single-OUT Flyback Controller 9.2V to 75V Input 6-Pin TSOT-23