- 您现在的位置：买卖IC网 > PDF目录1832 > LTC3822EGN-1#PBF (Linear Technology)IC REG CTRLR BUCK PWM CM 16-SSOP PDF资料下载
参数资料
| 型号： | LTC3822EGN-1#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 16/24页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 16-SSOP |
| 标准包装： | 100 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 850kHz |
| 占空比： | 99% |
| 电源电压： | 2.75 V ~ 4.5 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 产品目录页面： | 1336 (CN2011-ZH PDF) |
LTC3822-1
APPLICATIONS INFORMATION
1 ? V SENSE ( MAX )
I BURST ( PEAK ) = ?
R DS ( ON )
Burst Mode Operation Considerations
The choice of R DS(ON) and inductor value also determines
the load current at which the LTC3822-1 enters Burst Mode
operation. When bursting, the controller clamps the peak
inductor current to approximately:
4
Inductor Value Calculation
Given the desired input and output voltages, the inductor
value and operating frequency f OSC directly determine the
inductor’s peak-to-peak ripple current:
concentrate on copper loss and preventing saturation.
Ferrite core material saturates “hard,” which means that
inductance collapses abruptly when the peak design current
is exceeded. This results in an abrupt increase in inductor
ripple current and consequent output voltage ripple. Do
not allow the core to saturate!
Schottky Diode Selection (Optional)
The Schottky diode D in Figure 10 conducts current dur-
ing the dead time between the conduction of the power
MOSFETs. This prevents the body diode of the bottom
N-channel MOSFET from turning on and storing charge
during the dead time, which could cost as much as 1%
in ef?ciency. A 1A Schottky diode is generally a good size
I RIPPLE =
V OUT ? V IN – V OUT ?
V IN ? ? f OSC ? L ? ?
for most applications, since it conducts a relatively small
average current. Larger diodes result in additional transition
losses due to their larger junction capacitance. This diode
V OUT ? ( V IN OUT )
≈ I
C IN RMS MAX ?
Lower ripple current reduces core losses in the inductor,
ESR losses in the output capacitors, and output voltage
ripple. Thus, highest ef?ciency operation is obtained at
low frequency with a small ripple current. Achieving this,
however, requires a large inductor.
A reasonable starting point is to choose a ripple current
that is about 40% of I OUT(MAX) . Note that the largest ripple
current occurs at the highest input voltage. To guarantee
that ripple current does not exceed a speci?ed maximum,
the inductor should be chosen according to:
may be omitted if the ef?ciency loss can be tolerated.
C IN and C OUT Selection
In continuous mode, the source current of the top MOSFET
is a square wave of duty cycle (V OUT /V IN ). To prevent large
voltage transients, a low ESR input capacitor sized for the
maximum RMS current must be used. The maximum RMS
capacitor current is given by:
1 / 2
– V
Re quired I
V IN
V IN OUT
f OSC RIPPLE
? OUT
L ≥
– V
? I
V
V IN
This formula has a maximum value at V IN = 2V OUT , where
I RMS = I OUT /2. This simple worst-case condition is com-
monly used for design because even signi?cant deviations
Inductor Core Selection
Once the inductance value is determined, the type of in-
ductor must be selected. Core loss is independent of core
size for a ?xed inductor value, but it is very dependent
on inductance selected. As inductance increases, core
losses go down. Unfortunately, increased inductance
requires more turns of wire and therefore copper losses
will increase.
do not offer much relief. Note that capacitor manufacturer’s
ripple current ratings are often based on 2000 hours of life.
This makes it advisable to further derate the capacitor or
to choose a capacitor rated at a higher temperature than
required. Several capacitors may be paralleled to meet the
size or height requirements in the design. Due to the high
operating frequency of the LTC3822-1, ceramic capacitors
can also be used for C IN . Always consult the manufacturer
if there is any question.
Ferrite designs have very low core loss and are preferred
at high switching frequencies, so design goals can
38221f
16
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3822EMSE#TRPBF | IC REG CTRLR BUCK PWM CM 10-MSOP |
| LTC3823IUH#PBF | IC REG CTRLR BUCK PWM CM 32-QFN |
| LTC3824EMSE#PBF | IC REG CTRLR BUCK PWM CM 10-MSOP |
| LTC3826IUH#TRPBF | IC REG CTRLR BUCK PWM CM 32-QFN |
| LTC3827IG-1#TRPBF | IC REG CTRLR BUCK PWM CM 28-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3822EMSE#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3822EMSE#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3823EGN#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3823EGN#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3823EUH#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,000 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:50% 电源电压:9 V ~ 10 V 降压:无 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。