- 您现在的位置：买卖IC网 > PDF目录80040 > LTC3851AEGN#TRPBF (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, PDSO16 PDF资料下载
参数资料
| 型号： | LTC3851AEGN#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, PDSO16 |
| 封装： | 0.150 INCH, LEAD FREE, PLASTIC, SSOP-16 |
| 文件页数： | 5/30页 |
| 文件大小： | 430K |
| 代理商： | LTC3851AEGN#TRPBF |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LTC3851A
13
3851afa
applicaTions inForMaTion
VIN
INTVCC
BOOST
TG
SW
BG
GND
INDUCTOR
DCR
L
SENSE+
SENSE–
LTC3851A
VOUT
3851A F02
R1
R2
*PLACE C1 NEAR SENSE+, SENSE– PINS
C1*
R1||R2 C1 =
RSENSE(EQ) = DCR
L
DCR
R2
R1 + R2
Figure 2. Current Mode Control Using the Inductor DCR
Slope Compensation and Inductor Peak Current
Slope compensation provides stability in constant fre-
quency architectures by preventing sub-harmonic oscil-
lations at high duty cycles. It is accomplished internally
by adding a compensating ramp to the inductor current
signal. Normally, this results in a reduction of maximum
inductor peak current for duty cycles > 40%. However, the
LTC3851A uses a novel scheme that allows the maximum
inductor peak current to remain unaffected throughout all
duty cycles.
Inductor Value Calculation
The operating frequency and inductor selection are inter-
relatedinthathigheroperatingfrequenciesallowtheuseof
smaller inductor and capacitor values. A higher frequency
generally results in lower efficiency because of MOSFET
gate charge losses. In addition to this basic trade-off, the
effect of inductor value on ripple current and low current
operation must also be considered.
The inductor value has a direct effect on ripple current.
The inductor ripple current
IL decreases with higher
inductance or frequency and increases with higher VIN:
ΔIL =
1
f L
VOUT 1–
VOUT
VIN
Accepting larger values of
IL allows the use of low
inductances, but results in higher output voltage ripple
and greater core losses. A reasonable starting point for
setting ripple current is
IL = 0.3(IMAX). The maximum
IL occurs at the maximum input voltage.
The inductor value also has secondary effects. The tran-
sition to Burst Mode operation begins when the average
inductor current required results in a peak current below
≈10% of the current limit determined by RSENSE. Lower
inductor values (higher
IL) will cause this to occur at
lower load currents, which can cause a dip in efficiency in
the upper range of low current operation. In Burst Mode
operation, lower inductance values will cause the burst
frequency to increase.
Inductor Core Selection
Once the value for L is known, the type of inductor must
be selected. High efficiency converters generally cannot
afford the core loss found in low cost powdered iron cores,
forcingtheuseofmoreexpensiveferriteormolypermalloy
cores. Actual core loss is independent of core size for a
fixedinductorvalue,butitisverydependentoninductance
selected. As inductance increases, core losses go down.
Unfortunately, increased inductance requires more turns
of wire and therefore copper losses will increase.
Ferrite designs have very low core loss and are preferred
at high switching frequencies, so design goals can con-
centrate on copper loss and preventing saturation. Ferrite
core material saturates hard, which means that induc-
tance collapses abruptly when the peak design current is
exceeded. This results in an abrupt increase in inductor
ripple current and consequent output voltage ripple. Do
not allow the core to saturate!
Power MOSFET and Schottky Diode (Optional)
Selection
Two external power MOSFETs must be selected for the
LTC3851A controller: one N-channel MOSFET for the top
(main) switch, and one N-channel MOSFET for the bottom
(synchronous) switch.
相关PDF资料 |
PDF描述 |
|---|---|
| LQS50A48-2V5AKJ | 1-OUTPUT 200 W DC-DC REG PWR SUPPLY MODULE |
| LQS50A48-3V3RAKJ | 1-OUTPUT 200 W DC-DC REG PWR SUPPLY MODULE |
| LQS80A48-1V5EKJ | 1-OUTPUT 200 W DC-DC REG PWR SUPPLY MODULE |
| LM4040DIZ-10.0AP | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 10 V, PBCY3 |
| LM4040DIZ-10.0T&R | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 10 V, PBCY3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3851AEMSE#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LTC3851AEMSE#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3851AEMSE-1#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3851AEMSE-1#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3851AEUD#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。