- 您现在的位置：买卖IC网 > PDF目录1832 > LTC3852EUDD#PBF (Linear Technology)IC REG CTRLR DOUBLER PWM 24-QFN PDF资料下载
参数资料
| 型号： | LTC3852EUDD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 26/32页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR DOUBLER PWM 24-QFN |
| 标准包装： | 73 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 810kHz |
| 占空比： | 99% |
| 电源电压： | 2.7 V ~ 38 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 是 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页
LTC3852
APPLICATIONS INFORMATION
a minimum of 20μF to 40μF of capacitance having a
maximum of 20mΩ to 50mΩ of ESR. Other losses
including Schottky conduction losses during dead time
and inductor core losses generally account for less than
2% total additional loss.
Checking Transient Response
The regulator loop response can be checked by looking at
the load current transient response. Switching regulators
take several cycles to respond to a step in DC (resistive)
load current. When a load step occurs, V OUT shifts by an
amount equal to D I LOAD (ESR), where ESR is the effective
series resistance of C OUT . D I LOAD also begins to charge or
discharge C OUT generating the feedback error signal that
forces the regulator to adapt to the current change and
return V OUT to its steady-state value. During this recovery
time V OUT can be monitored for excessive overshoot or
ringing, which would indicate a stability problem. The
availability of the I TH pin not only allows optimization of
control loop behavior but also provides a DC coupled and
AC ?ltered closed-loop response test point. The DC step,
rise time and settling at this test point truly re?ects the
closed-loop response. Assuming a predominantly second
order system, phase margin and/or damping factor can be
estimated using the percentage of overshoot seen at this
pin. The bandwidth can also be estimated by examining the
rise time at the pin. The I TH external components shown
in the Typical Application circuit will provide an adequate
starting point for most applications.
The I TH series R C -C C ?lter sets the dominant pole-zero
loop compensation. The values can be modi?ed slightly
(from 0.5 to 2 times their suggested values) to optimize
transient response once the ?nal PC layout is done and
the particular output capacitor type and value have been
determined. The output capacitors need to be selected
because the various types and values determine the loop
gain and phase. An output current pulse of 20% to 80%
of full-load current having a rise time of 1μs to 10μs will
produce output voltage and I TH pin waveforms that will
give a sense of the overall loop stability without breaking
the feedback loop. Placing a power MOSFET directly
across the output capacitor and driving the gate with an
appropriate signal generator is a practical way to produce
a realistic load step condition. The initial output voltage
step resulting from the step change in output current may
not be within the bandwidth of the feedback loop, so this
signal cannot be used to determine phase margin. This
is why it is better to look at the I TH pin signal which is in
the feedback loop and is the ?ltered and compensated
control loop response. The midband gain of the loop will
be increased by increasing R C and the bandwidth of the
loop will be increased by decreasing C C . If R C is increased
by the same factor that C C is decreased, the zero frequency
will be kept the same, thereby keeping the phase shift the
same in the most critical frequency range of the feedback
loop. The output voltage settling behavior is related to the
stability of the closed-loop system and will demonstrate
the actual overall supply performance.
A second, more severe transient is caused by switching
in loads with large (>1μF) supply bypass capacitors. The
discharged bypass capacitors are effectively put in parallel
with C OUT , causing a rapid drop in V OUT . No regulator can
alter its delivery of current quickly enough to prevent this
sudden step change in output voltage if the load switch
resistance is low and it is driven quickly. If the ratio of
C LOAD to C OUT is greater than 1:50, the switch rise time
should be controlled so that the load rise time is limited
to approximately 25 ? C LOAD . Thus a 10μF capacitor would
require a 250μs rise time, limiting the charging current
to about 200mA.
PC Board Layout Checklist
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of
the LTC3852. These items are also illustrated graphically
in the layout diagram of Figure 13. Check the following
in your layout:
1. Are the board signal and power grounds segregated?
The LTC3852 ground pins should connect to the ground
plane close to the output capacitor(s). The low current
or signal ground lines should make a single point tie
directly to the GND1 and GND2 pins. The synchronous
MOSFET source pins should connect to the input
capacitor(s) ground.
2. Does the V FB pin connect directly to the feedback
resistors? The resistive divider R1, R2 must be
connected between the (+) plate of C OUT and signal
3852f
26
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3853EUJ#PBF | IC REG CTRLR BUCK PWM CM 40-QFN |
| LTC3854EMSE#PBF | IC REG CTRLR BUCK PWM CM 12-MSOP |
| LTC3855IUJ#PBF | IC REG CTRLR BUCK PWM CM 40-QFN |
| LTC3856IFE#TRPBF | IC REG CTRLR BUCK PWM CM 38TSSOP |
| LTC3858IUH#TRPBF | IC REG CTRLR BUCK PWM CM 32-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3852IUDD#PBF | 功能描述:IC REG CTRLR DOUBLER PWM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3852IUDD#TRPBF | 功能描述:IC REG CTRLR DOUBLER PWM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3853EUJ#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 40-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LTC3853EUJ#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 40-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LTC3853EUJPBF | 制造商:Linear Technology 功能描述:DC-DC Controller Triple Buck 24V QFN40 |
发布紧急采购，3分钟左右您将得到回复。