- 您现在的位置：买卖IC网 > PDF目录80307 > LTC4000IGN#TRPBF (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO28 PDF资料下载
参数资料
| 型号： | LTC4000IGN#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO28 |
| 封装： | 0.150 INCH, LEAD FREE, PLASTIC, SSOP-28 |
| 文件页数： | 8/40页 |
| 文件大小： | 428K |
| 代理商： | LTC4000IGN#TRPBF |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
LTC4000
16
4000f
operaTion
to be approximately 86% of the final float voltage level
(VOUT(INST_ON)). This feature provides a CSP voltage sig-
nificantly higher than the battery voltage when charging
into a heavily discharged battery. This instant-on feature
allows the LTC4000 to provide sufficient voltage at the
output (CSP pin), independent of the battery voltage.
Thesecondregionofoperationiswhenthebatteryfeedback
voltage is greater than or equal to the instant-on threshold
(VOUT(INST_ON)). In this region, the BGATE pin is driven
low and clamped at VBGATE(ON) to allow the PMOS to turn
completely on, reducing any power dissipation due to the
charge current.
Battery Temperature Qualified Charging
The battery temperature is measured by placing a nega-
tive temperature coefficient (NTC) thermistor close to the
battery pack. The comparators CP3 and CP4 implement
the temperature detection as shown in the Block Diagram
in Figure 1. The rising threshold of CP4 is set at 75% of
VBIAS (cold threshold) and the falling threshold of CP3 is
set at 35% of VBIAS (hot threshold). When the voltage at
the NTC pin is above 75% of VBIAS or below 35% of VBIAS
then the LTC4000 pauses any charge cycle in progress.
When the voltage at the NTC pin returns to the range of
40% to 70% of VBIAS, charging resumes.
When charging is paused, the external charging PMOS
turns off and charge current drops to zero. If the LTC4000
is charging in the constant voltage mode and the charge
termination timer is enabled, the timer pauses until the
thermistor indicates a return to a valid temperature. If the
battery charger is in the trickle charge mode and the bad
battery detection timer is enabled, the bad battery timer
pauses until the thermistor indicates a return to a valid
temperature.
Input UVLO and Voltage Monitoring
The regulated voltage on the BIAS pin is available as soon
as VIN ≥ 3V. When VIN ≥ 3V, the FBG pin is pulled low to
GND with a typical resistance of 100Ω and the rest of the
chip functionality is enabled.
When the IN pin is high impedance and a battery is con-
nected to the BAT pin, the BGATE pin is pulled down with
a 2μA (typical) current source to hold the battery PMOS
gate voltage at VBGATE(ON) below VBAT. This allows the
battery to power the output. The total quiescent current
consumed by LTC4000 from the battery when IN is not
valid is typically ≤ 10A.
BesidestheinternalinputUVLO,theLTC4000alsoprovides
voltage monitoring through the VM pin. The RST pin is
pulled low when the voltage on the VM pin falls below
1.193V (typical). On the other hand, when the voltage on
the VM pin rises above 1.233V (typical), the RST pin is
high impedance.
One common use of this voltage monitoring feature is to
ensure that the converter is turned off when the voltage
at the input is below a certain level. In this case, connect
the RST pin to the DC/DC converter chip select or enable
pin (see Figure 6).
Figure 6. Input Voltage Monitoring with RST Connected to
the EN Pin of the DC/DC Converter
IN
CP1
LTC4000
IN
CLN
RST
RIS
VM
4000 FO6
RVM2
RVM1
1.193V
+
–
IN
DC/DC
CONVERTER
EN
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4155EUFD#TRPBF | POWER SUPPLY SUPPORT CKT, PQCC28 |
| LM4040BIZ-5.0AMMOPACK | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 5 V, PBCY3 |
| L296VH | 4 A SWITCHING REGULATOR, 200 kHz SWITCHING FREQ-MAX, PZFM15 |
| LM9140BYM-2.5 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, PDSO8 |
| LK5540-7ERD0TB1 | 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4000IUFD#PBF | 功能描述:IC CHARGER BATTERY 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4000IUFD#TRPBF | 功能描述:IC CHARGER BATTERY 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4000IUFD-1#PBF | 功能描述:IC BATT CHRGR MULTI-CHEM 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 标准包装:2,000 系列:Impedance Track™ 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.4 V ~ 2.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:带卷 (TR) 产品目录页面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名称:296-21665-2 |
| LTC4000IUFD-1#TRPBF | 功能描述:IC CHARGE MGMT MULTI CHEM 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4001 | 制造商:LINER 制造商全称:Linear Technology 功能描述:2A Synchronous Buck Li-Ion Charger |
发布紧急采购，3分钟左右您将得到回复。