- 您现在的位置：买卖IC网 > PDF目录15996 > LTC4009IUF-2#PBF (Linear Technology)IC CHARGER BATTERY MC 20-QFN PDF资料下载
参数资料
| 型号： | LTC4009IUF-2#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/28页 |
| 文件大小： | 0K |
| 描述： | IC CHARGER BATTERY MC 20-QFN |
| 标准包装： | 91 |
| 功能： | 充电管理 |
| 电池化学： | 多化学 |
| 电源电压： | 6 V ~ 28 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 供应商设备封装： | 20-QFN 裸露焊盘（4x4） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC4009
LTC4009-1/LTC4009-2
PIN FUNCTIONS
FVS0 (Pin 9, LTC4009-1/LTC4009-2): Battery Voltage
Select Input (LSB). This pin is one of two pins used on the
LTC4009-1 or LTC4009-2 to select one of four preset battery
voltages. Selection is done by connecting to either GND or
INTV DD . Operating voltage range is GND to INTV DD .
V FB (Pin 10, LTC4009): Battery Voltage Feedback Input. An
external resistor divider between FBDIV and GND with the
center tap connected to V FB programs the charger output
voltage. In constant voltage mode, this pin is nominally
at 1.2085V. Refer to the Applications Information section
for complete details on programming battery float voltage.
Operating voltage range is GND to 1.25V.
FVS1 (Pin 10, LTC4009-1/LTC4009-2): Battery Voltage
Select Input (MSB). This pin is one of two pins used on
the LTC4009-1 or LTC4009-2 to select one of four preset
battery voltages. Selection is done by connecting to
either GND or INTV DD . Operating voltage range is GND
to INTV DD .
BAT (Pin 11): Battery Pack Connection. The LTC4009 uses
the voltage on this pin to control PWM operation when
charging. Operating voltage range is GND to CLN.
ITH (Pin 12): PWM Control Voltage and Compensation
Node. The LTC4009 develops a voltage on this pin to
control cycle-by-cycle peak inductor current. An external
R-C network connected to ITH provides PWM loop com-
pensation. Refer to the Applications Information section
for further details on establishing loop stability. Operating
voltage range is GND to INTV DD .
PROG (Pin 13): Charge Current Programming and Monitor-
ing Pin. An external resistance connected between PROG
and GND, along with the current sense and PWM input
resistors, programs the maximum charge current. The
voltage on this pin can also provide a linearized indicator
of charge current. Refer to the Applications Information
section for complete details on current programming and
monitoring. Operating voltage range is GND to INTV DD .
CSN (Pin 14): Charge Current Sense Negative In-
put. Place an external input resistor (R IN , Figure 1)
between this pin and the negative side of the charge
current sense resistor. Operating voltage ranges from
(BAT – 50mV) to (BAT + 200mV).
CSP (Pin 15): Charge Current Sense Positive Input.
Place an external input resistor (R IN , Figure 1) be-
tween this pin and the positive side of the charge
current sense resistor. Operating voltage ranges from
(BAT – 50mV) to (BAT + 200mV).
BGATE (Pin 16): External Synchronous NFET Gate Control
Output. This output provides gate drive to an external NMOS
power transistor switch used for synchronous rectification
to increase efficiency in the step-down DC/DC converter.
Operating voltage is GND to INTV DD . BGATE should be
left floating if not used.
INTV DD (Pin 17): Internal 5V Regulator Output. This pin
provides a means of bypassing the internal 5V regulator
used to power the LTC4009 PWM FET drivers. This supply
shuts down when the LTC4009 shuts down. Refer to the
Application Information section for details if additional
power is drawn from this pin by the application circuit.
SW (Pin 18): PWM Switch Node. The LTC4009 uses the
voltage on this pin as the source reference for its topside
NFET (PWM switch) driver. Refer to the Applications In-
formation section for additional PCB layout suggestions
related to this critical circuit node. Operating voltage range
is GND to CLN.
TGATE (Pin 19): External NFET Switch Gate Control Output.
This output provides gate drive to an external NMOS power
transistor switch used in the DC/DC converter. Operating
voltage range is GND to (CLN + 5V).
BOOST (Pin 20): TGATE Driver Supply Input. A bootstrap
capacitor is returned to this pin from a charge network
connected to SW and INTV DD . Refer to the Applications
Information section for complete details on circuit topol-
ogy and component values. Operating voltage ranges from
(INTV DD – 1V) to (CLN + 5V).
GND (Exposed Pad Pin 21): Ground. The package paddle
provides a single-point ground for the internal voltage
reference and other critical LTC4009 circuits. It must be
soldered to a suitable PCB copper ground pad for proper
electrical operation and to obtain the specified package
thermal resistance.
4009fd
相关PDF资料 |
PDF描述 |
|---|---|
| M3RRK-3420K | IDC CABLE - MPR34K/MC34F/MPR34K |
| 450QXW39MEFC10X40 | CAP ALUM 39UF 450V 20% RADIAL |
| LT1571EGN-5#TRPBF | IC CHARGER BATT CONST V/I 16SSOP |
| 415-0009-030 | CABLE SMB-RA/SMB-RA 30" RG-179 |
| 63RX30330MG412.5X25 | CAP ALUM 330UF 63V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4010 | 制造商:LINEAR 制造商全称:LINEAR 功能描述:High Efficiency Standalone Nickel Battery Charger |
| LTC4010CFE | 制造商:Linear Technology 功能描述:Battery Charger NiCD/NiMH 16-Pin TSSOP EP |
| LTC4010CFE#PBF | 功能描述:IC CHARGER NIMH/NICD 16-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4010CFE#PBF | 制造商:Linear Technology 功能描述:CHARGER BATT NICKEL 34V 16TSSOP 制造商:Linear Technology 功能描述:CHARGER, BATT, NICKEL, 34V, 16TSSOP |
| LTC4010CFE#TRPBF | 功能描述:IC CHARGER NIMH/NICD 16-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。