- 您现在的位置：买卖IC网 > PDF目录1833 > LTC4010CFE#TRPBF (Linear Technology)IC CHARGER NIMH/NICD 16-TSSOP PDF资料下载
参数资料
| 型号： | LTC4010CFE#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/24页 |
| 文件大小： | 0K |
| 描述： | IC CHARGER NIMH/NICD 16-TSSOP |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 镍镉（NiCd）、镍金属氢化物（NiMH） |
| 电源电压： | 4.5 V ~ 34 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 供应商设备封装： | 16-TSSOP-EP |
| 包装： | 带卷 (TR) |
LTC4010
OPERATION
(Refer to Figure 1)
Shutdown State
The LTC4010 remains in micropower shutdown until V CC
(Pin 15) is driven above BAT (Pin 10). In shutdown all
status and PWM outputs and internally generated supply
voltages are inactive. Current consumption from V CC and
BAT is reduced to a very low level.
Charge Qualification State
Once V CC is greater than BAT, the LTC4010 exits micropower
shutdown, enables its own internal supplies and switches
V CDIV to GND to allow measurement of the average single-
cell voltage. The IC also verifies that V CC is at or above 4.2V,
V CC is 510mV above BAT and V CELL is between 350mV and
1.95V. If V CELL is below 350mV, no charging will occur, and
if V CELL is above 1.95V, the fault state is entered, which
is described in more detail below. Once adequate voltage
conditions exist for charging, READY is asserted.
If the voltage between V TEMP and GND is below 200mV, the
LTC4010 is paused. If V TEMP is above 200mV but below
2.85V, the LTC4010 verifies that the sensed temperature
is between 5°C and 45°C. If these temperature limits
are not met or if its own die temperature is too high, the
LTC4010 will indicate a fault and not allow charging to
begin. If V TEMP is greater than 2.85V, battery temperature
related charge qualification, monitoring and termination
are disabled.
Once charging is fully qualified, precharge begins (unless
the LTC4010 is paused). In that case, the V TEMP pin is
monitored for further control. The charge status indicators
and PWM outputs remain inactive until charging begins.
Charge Monitoring
The LTC4010 continues to monitor important voltage and
temperature parameters during all charging states. If V CC
drops to the BAT voltage or lower, charging stops and the
shutdown state is entered. If V CC drops below 4.25V or
V CELL drops below 350mV, charging stops and the LTC4010
returns to the charge qualification state. If V CELL exceeds
1.95V, charging stops and the IC enters the fault state. If an
external thermistor indicates sensed temperature is beyond
a range of 5°C to 60°C, or the internal die temperature
exceeds a resonable value, charging is suspended, the
charge timer is paused and the LTC4010 indicates a fault
condition. Normal charging resumes from the previous
state when the sensed temperature returns to a satisfactory
range. In addition, other battery faults are detected during
specific charging states as described below.
Precharge State
If the initial voltage on V CELL is below 900mV, the LTC4010
enters the precharge state and enables the PWM current
source to trickle charge using one-fifth the programmed
charge current. The CHRG status output is active during
precharge. The precharge state duration is limited to
t MAX /12 minutes, where t MAX is the maximum fast charge
period programmed with the TIMER pin. If sufficient V CELL
voltage cannot be developed in this length of time, the fault
state is entered, otherwise fast charge begins.
Fast Charge State
If adequate average single-cell voltage exists, the LTC4010
enters the fast charge state and begins charging at the
programmed current set by the external current sense
resistor connected between the SENSE and BAT pins.
The CHRG status output is active during fast charge. If
V CELL is initially above 1.325V, voltage-based termination
processing begins immediately. Otherwise –?V termination
is disabled for a stabilization period of t MAX /12. In that
case, the LTC4010 makes another fault check at t MAX /12,
requiring the average cell voltage to be above 1.22V. This
ensures the battery pack is accepting a fast charge. If
V CELL is not above this voltage threshold, the fault state is
entered. Fast charge state duration is limited to t MAX and
the fault state is entered if this limit is exceeded.
4010fb
0
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4011CFE#TRPBF | IC BATT CHARGER HIEFF 20TSSOP |
| LTC4012IUF-3#TRPBF | IC CTLR BATT CHARGER CC/CV 20QFN |
| LTC4050EMS-4.1#TR | IC BATT CHRG CNTRL LI-ION 10MSOP |
| LTC4052EMS8E-4.2#TRPBF | IC CHARGER PULSE LI-ION 8-MSOP |
| LTC4053EDD-4.2#TRPBF | IC CHARGER BATTERY USB 10-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4010EFE | 制造商:LINEAR 制造商全称:LINEAR 功能描述:High Efficiency Standalone Nickel Battery Charger |
| LTC4011 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency Standalone Nickel Battery Charger |
| LTC4011_1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency Standalone Nickel Battery Charger |
| LTC4011CFE | 功能描述:IC BATT CHARGER HIEFF 20TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4011CFE#PBF | 功能描述:IC BATT CHARGER HIEFF 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
发布紧急采购，3分钟左右您将得到回复。