- 您现在的位置：买卖IC网 > PDF目录1833 > LTC4010CFE#TRPBF (Linear Technology)IC CHARGER NIMH/NICD 16-TSSOP PDF资料下载
参数资料
| 型号： | LTC4010CFE#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/24页 |
| 文件大小： | 0K |
| 描述： | IC CHARGER NIMH/NICD 16-TSSOP |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 镍镉（NiCd）、镍金属氢化物（NiMH） |
| 电源电压： | 4.5 V ~ 34 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 供应商设备封装： | 16-TSSOP-EP |
| 包装： | 带卷 (TR) |
LTC4010
PIN FUNCTIONS
GND (Pin 4): Ground. This pin provides a single-point
ground for internal references and other critical analog
circuits.
V TEMP (Pin 5): Battery Temperature Input. An external 10k
NTC thermistor may be connected between V TEMP and
GND to provide temperature-based charge qualification
and additional fast charge termination control. Charging
may also be paused by connecting the V TEMP pin to GND.
Refer to the Operation and Applications Information sec-
tions for complete details on external thermistor networks
and charge control. If this pin is not used it should be
wired to GND through 10k. Operating voltage range is
GND to 3.3V.
V CELL (Pin 6): Average Single-Cell Voltage Input. An external
voltage divider between BAT and V CDIV is attached to this
pin to monitor the average single-cell voltage of the bat-
tery pack. The LTC4010 uses this information to protect
against catastrophic battery overvoltage and to control
the charging state. Refer to the Applications Information
section for further details on the external divider network.
Operating voltage range is GND to BAT.
V CDIV (Pin 7): Average Cell Voltage Resistor Divider Termi-
nation. The LTC4010 connects this pin to GND provided the
charger is not in shutdown. V CDIV is an open-drain output
to GND with an operating voltage range of GND to BAT.
TIMER (Pin 8): Charge Timer Input. A resistor connected
between TIMER and GND programs charge cycle timing
limits. Refer to the Applications Information section for
complete details. Operating voltage range is GND to 1V.
SENSE (Pin 9): Charge Current Sense Input. An external
resistor between this input and BAT is used to program
charge current. Refer to the Applications Information
section for complete details on programming charge
current. Operating voltage ranges from (BAT – 50mV) to
(BAT + 200mV).
BAT (Pin 10): Battery Pack Connection. The LTC4010 uses
the voltage on this pin to control current sourced from
V CC to the battery during charging. Allowable operating
voltage range is GND to V CC .
INTV DD (Pin 11): Internal 5V Regulator Output. This pin
provides a means of bypassing the internal 5V regulator
used to power the BGATE output driver. Typically, power
should not be drawn from this pin by the application
circuit. Refer to the Application Information section for
additional details.
BGATE (Pin 12): External Synchronous N-channel MOSFET
Gate Control Output. This output provides gate drive to
an optional external NMOS power transistor switch used
for synchronous rectification to increase efficiency in the
step-down DC/DC converter. Operating voltage is GND to
INTV DD . BGATE should be left floating if not used.
PGND (Pin 13): Power Ground. This pin provides a return
for switching currents generated by internal LTC4010 cir-
cuits. Externally, PGND and GND should be wired together
using a very low impedance connection. Refer to PCB
Layout Considerations in the Applications Information
section for additional grounding details.
TGATE (Pin 14): External P-channel MOSFET Gate Control
Output. This output provides gate drive to an external PMOS
power transistor switch used in the DC/DC converter. Op-
erating voltage range varies as a function of V CC . Refer to
the Electrical Characteristics table for specific voltages.
V CC (Pin 15): Power Input. External diodes normally
connect either the DC input power supply or the battery
to this pin. Refer to the Applications Information section
for further details. Suggested applied voltage range is
GND to 34V.
READY (Pin 16): Active-Low Ready-to-Charge Output.
The LTC4010 connects this pin to GND if proper operating
voltages for charging are present. Refer to the Operation
section for complete details on charge qualification. This
output is capable of driving an LED and should be left
floating if not used. READY is an open-drain output to
GND with an operating voltage range of GND to V CC .
Exposed Pad (Pin 17): This pin provides enhanced thermal
properties for the TSSOP. It must be soldered to the PCB
copper ground to obtain optimum thermal performance.
4010fb
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4011CFE#TRPBF | IC BATT CHARGER HIEFF 20TSSOP |
| LTC4012IUF-3#TRPBF | IC CTLR BATT CHARGER CC/CV 20QFN |
| LTC4050EMS-4.1#TR | IC BATT CHRG CNTRL LI-ION 10MSOP |
| LTC4052EMS8E-4.2#TRPBF | IC CHARGER PULSE LI-ION 8-MSOP |
| LTC4053EDD-4.2#TRPBF | IC CHARGER BATTERY USB 10-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4010EFE | 制造商:LINEAR 制造商全称:LINEAR 功能描述:High Efficiency Standalone Nickel Battery Charger |
| LTC4011 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency Standalone Nickel Battery Charger |
| LTC4011_1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency Standalone Nickel Battery Charger |
| LTC4011CFE | 功能描述:IC BATT CHARGER HIEFF 20TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4011CFE#PBF | 功能描述:IC BATT CHARGER HIEFF 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
发布紧急采购，3分钟左右您将得到回复。