- 您现在的位置：买卖IC网 > PDF目录1833 > LTC4010CFE#TRPBF (Linear Technology)IC CHARGER NIMH/NICD 16-TSSOP PDF资料下载
参数资料
| 型号： | LTC4010CFE#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 17/24页 |
| 文件大小： | 0K |
| 描述： | IC CHARGER NIMH/NICD 16-TSSOP |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 镍镉（NiCd）、镍金属氢化物（NiMH） |
| 电源电压： | 4.5 V ~ 34 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 供应商设备封装： | 16-TSSOP-EP |
| 包装： | 带卷 (TR) |
LTC4010
APPLICATIONS INFORMATION
Sample Applications
Figures 6 through 8 detail sample charger applications of
various complexities. Combined with the Typical Application
on the first page of this data sheet, these figures demon-
strate some of the proper configurations of the LTC4010.
MOSFET body diodes are shown in these figures strictly
for reference only.
Figure 6 shows a minimum application, which might be
encountered in low cost NiCd fast charge applications.
The LTC4010 uses –?V to terminate the fast charge state,
as no external temperature information is available.
Nonsynchronous PWM switching is employed to reduce
external component cost. A single LED indicates charging
status.
A full-featured 2A LTC4010 application is shown in Figure 7.
The inherent voltage ratings of the V CELL , V CDIV , SENSE
and BAT pins allow charging of one to sixteen series nickel
cells in this application, governed only by the V CC overhead
limits previously discussed. The application includes all
average cell voltage and battery temperature sensing
circuitry required for the LTC4010 to utilize its full range
of charge qualification, safety monitoring and fast charge
termination features. The V TEMP thermister network allows
the LTC4010 to accurately terminate fast charge under a
variety of applied charge rates. Use of a synchronous PWM
topology improves efficiency and reduces excess heat
generation. LED D1 indicates valid DC input voltage and
installed battery, while LED D2 indicates charging. Fault
conditions are indicated by LED D3. The grounded CHEM
pin selects the NiMH charge termination parameter set.
P-channel MOSFET Q1 functions as a switch to connect the
battery to the system load whenever the DC input adapter
is removed. If the maximum battery voltage is less than
the maximum rated V GS of Q1, diode D4 and resistor R1
are not required. Otherwise choose the Zener voltage
of D4 to be less than the maximum rated V GS of Q1. R1
provides a bias current of (V BAT – V ZENER )/(R1 + 20k) for
D4 when the input adapter is removed. Choose R1 to make
this current, which is drawn from the battery, just large
enough to develop the desired V GS across D4.
While the LTC4010 is a complete, standalone solution,
Figure 8 shows that it can also be interfaced to a host
microprocessor. The host MCU can control the charger
directly with an open-drain I/O port connected to the V TEMP
pin, if that port is low leakage and can tolerate at least
2V. The charger state is monitored on the three LTC4010
status outputs. Charging of NiMH batteries is selected in
this example. However, NiCd parameters could be chosen
as well.
FROM
ADAPTER
12V
3k
10μF
LTC4010
FAULT TGATE
V CC
TO
SYSTEM
LOAD
CHRG
READY
BGATE
TIMER
PGND
10μH
49.9k
GND
SENSE
0.1
0.1μF
BAT
V CDIV
CHEM V CELL
INTV DD V TEMP
8.66k
10k
R2
33nF
10μF
4010 F06
NiCd
PACK
(1AHr)
Figure 6. Minimum 1 Amp LTC4010 Application
4010fb
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4011CFE#TRPBF | IC BATT CHARGER HIEFF 20TSSOP |
| LTC4012IUF-3#TRPBF | IC CTLR BATT CHARGER CC/CV 20QFN |
| LTC4050EMS-4.1#TR | IC BATT CHRG CNTRL LI-ION 10MSOP |
| LTC4052EMS8E-4.2#TRPBF | IC CHARGER PULSE LI-ION 8-MSOP |
| LTC4053EDD-4.2#TRPBF | IC CHARGER BATTERY USB 10-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4010EFE | 制造商:LINEAR 制造商全称:LINEAR 功能描述:High Efficiency Standalone Nickel Battery Charger |
| LTC4011 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency Standalone Nickel Battery Charger |
| LTC4011_1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency Standalone Nickel Battery Charger |
| LTC4011CFE | 功能描述:IC BATT CHARGER HIEFF 20TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4011CFE#PBF | 功能描述:IC BATT CHARGER HIEFF 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
发布紧急采购，3分钟左右您将得到回复。