- 您现在的位置：买卖IC网 > PDF目录1833 > LTC4062EDD#TRPBF (Linear Technology)IC BATT CHARGER LI-ION 10-DFN PDF资料下载
参数资料
| 型号： | LTC4062EDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 16/20页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER LI-ION 10-DFN |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 4.3 V ~ 8 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-DFN（3x3） |
| 包装： | 带卷 (TR) |
LTC4062
APPLICATIO S I FOR ATIO
105 ° C – T A
I BAT =
I BAT =
=
Example: An LTC4062 operating from a 5V wall adapter is
programmed to supply 800mA full-scale current to a
discharged Li-Ion battery with a voltage of 3.3V. Assuming
θ JA is 40 ° C/W (see Thermal Considerations), the ambient
temperature at which the LTC4062 will begin to reduce the
charge current is approximately:
T A = 105 ° C – (5V – 3.3V) ? (800mA) ? 40 ° C/W
T A = 105 ° C – 1.36W ? 40 ° C/W = 105 ° C – 54.4 ° C
T A = 50.6 ° C
The LTC4062 can be used above 50.6 ° C ambient, but the
charge current will be reduced from 800mA. The approxi-
mate current at a given ambient temperature can be
approximated by:
( V CC – V BAT )? θ JA
Using the previous example with an ambient temperature
of 60 ° C, the charge current will be reduced to
approximately:
105 ° C – 60 ° C 45 ° C
( 5 V – 3 . 3 V ) ? 40 ° C / W 68 ° C / A
I BAT = 662 mA
It is important to remember that LTC4062 applications do
not need to be designed for worst-case thermal condi-
tions, since the IC will automatically reduce power dissi-
pation if the junction temperature reaches approximately
105 ° C.
Thermal Considerations
In order to deliver maximum charge current under all
conditions, it is critical that the exposed metal pad on the
backside of the LTC4062 package is properly soldered to
the PC board ground. Correctly soldered to a 2500mm 2
correctly soldered LTC4062 can deliver over 800mA to a
battery from a 5V supply at room temperature. Without a
good backside thermal connection, this number could
drop to less than 500mA.
V CC Bypass Capacitor
Many types of capacitors can be used for input bypassing;
however, caution must be exercised when using multi-
layer ceramic capacitors. Because of the self-resonant and
high Q characteristics of some types of ceramic capaci-
tors, high voltage transients can be generated under some
start-up conditions such as connecting the charger input
to a live power source. Adding a 1.5 ? resistor in series
with an X5R ceramic capacitor will minimize start-up
voltage transients. For more information, see Application
Note 88.
Charge Current Soft-Start and Soft-Stop
The LTC4062 includes a soft-start circuit to minimize the
inrush current at the start of a charge cycle. When a charge
cycle is initiated, the charge current ramps from zero to the
full-scale current over a period of approximately 100 μ s.
Likewise, internal circuitry slowly ramps the charge cur-
rent from full-scale to zero when the charger is shut off or
self terminates. This has the effect of minimizing the
transient current load on the power supply during start-up
and charge termination.
Reverse Polarity Input Voltage Protection
In some applications, protection from reverse polarity on
V CC is desired. If the supply voltage is high enough, a
series blocking diode can be used. In other cases, where
the diode voltage drop must be kept low, a P-channel
MOSFET can be used (as shown in Figure 7).
DRAIN-BULK
DIODE OF FET
double sided 1oz copper board, the LTC4062 has a ther-
mal resistance of approximately 40 ° C/W. Failure to make
V IN
LTC4062
V CC
thermal contact between the exposed pad on the backside
of the package and the copper board will result in thermal
resistances far greater than 40 ° C/W. As an example, a
4062 F07
Figure 7. Low Loss Input Reverse Polarity Protection
4062fb
16
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4063EDD#TRPBF | IC BATT CHRGR LI-ION LDO 10DFN |
| LTC4064EMSE#TRPBF | IC CHARGER BATT L-ION 4V 10-MSOP |
| LTC4065EDC#TRPBF | IC CHARGER BATT LI-ON 6-DFN |
| LTC4066EPF#TRPBF | IC USB POWER MANAGER 24-UTQFN |
| LTC4067EDE#TRPBF | IC USB POWER MANAGER 12-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4063 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Standalone Linear Li-lon Battery Charger with Thermistor Input |
| LTC4063EDD | 功能描述:IC BATT CHRGR LI-ION LDO 10DFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4063EDD#PBF | 功能描述:IC BATT CHRGR LI-ION LDO 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4063EDD#TRPBF | 功能描述:IC BATT CHRGR LI-ION LDO 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4064 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic Linear Charger for Back-Up Li-Ion Batteries |
发布紧急采购，3分钟左右您将得到回复。