- 您现在的位置：买卖IC网 > PDF目录1833 > LTC4062EDD#TRPBF (Linear Technology)IC BATT CHARGER LI-ION 10-DFN PDF资料下载
参数资料
| 型号： | LTC4062EDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/20页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER LI-ION 10-DFN |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 4.3 V ~ 8 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-DFN（3x3） |
| 包装： | 带卷 (TR) |
LTC4062
PI FU CTIO S
BAT (Pin 1): Charge Current Output. This pin provides
charge current to the battery and regulates the final float
voltage to 4.2V.
IN + (Pin 2): Positive Input of the Micropower Comparator.
The negative input is tied internally to a precise bandgap
voltage reference of 1V. There is approximately 50mV of
hysteresis associated with the input comparator threshold
(rising edge).
TIMER (Pin 3): Timer Program and Termination Select
Pin. This pin selects which method is used to terminate the
charge cycle. Connecting a capacitor, C TIMER , to ground
selects charge time termination. The charge time is set by
the following formula:
C/5 (Pin 6): C/5 Enable Input. Used to control the amount
of current drawn by the charger when powered from a USB
port. A logic high on the C/5 pin sets the current limit to
100% of the current programmed by the PROG pin. A logic
low on the C/5 pin sets the current limit to 20% of the current
programmed by the PROG pin. An internal 3M ? pull-down
resistor defaults the C/5 pin to its low current state.
EN (Pin 7): Charger Enable Input. A logic high on the EN
pin places the charger into shutdown mode, where the
input quiescent current is less than 50 μ A. A logic low on
this pin enables charging. An internal 3M ? pull-down
resistor to ground defaults the charger to its enabled state.
I DET (Pin 8): Current Detection Threshold Program Pin.
The current detection threshold, I DETECT , is set by con-
TIME ( HOURS ) = 3 ( HOURS ) ?
C TIMER
0 . 1 μ F
or
necting a resistor, R DETECT , to ground. I DETECT is set by the
following formula:
C TIMER = 0 . 1 μ F ?
TIME ( HOURS )
3 ( HOURS )
I DETECT =
R PROG
10 R DET
? I CHG =
100 V
R DET
or
Connecting the TIMER pin to ground selects charge cur-
rent termination, while connecting the pin to V CC selects
user termination. See Applications Information for more
R DET =
100 V
I DETECT
information on current and user termination.
OUT (Pin 4): Low Power Comparator Open-Drain Output.
This comparator output pin has two states; pull-down and
high impedance. This output can be used as a logic
interface or as an LED driver. In the pull-down state, an
NMOS transistor capable of sinking 10mA pulls down on
the OUT pin. The state of this pin is dependent on the value
of IN + . When IN + is greater than 1V the output pin is in pull-
down state, if IN + is less than 1V the output pin is in high
impedance state. See Applications Information.
CHRG (Pin 5): Open-Drain Charge Status Output. The
charge status indicator pin has three states: pull-down,
pulse at 6Hz and high impedance. This output can be used
as a logic interface or as a LED driver. In the pull-down
state, an NMOS transistor capable of sinking 10mA pulls
down on the CHRG pin. The state of this pin depends on the
The CHRG pin becomes high impedance when the charge
current drops below I DETECT . I DETECT can be set to 1/10th
the programmed charge current by connecting I DET di-
rectly to PROG. If the I DET pin is not connected, the CHRG
output remains in its pull-down state until the charge time
elapses and terminates the charge cycle. See Applications
Information.
This pin is clamped to approximately 2.4V. Driving this pin
to voltages beyond the clamp voltage should be avoided.
PROG (Pin 9): Charge Current Program and Charge Cur-
rent Monitor. The charge current is set by connecting a
resistor, R PROG , to ground. When charging in constant
current mode, this pin servos to 1V. The voltage on this pin
can be used to measure the charge current using the
following formula:
value of I DETECT as well as the termination method being
used. See Applications Information.
I BAT =
V PROG
R PROG
? 1000
4062fb
7
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4063EDD#TRPBF | IC BATT CHRGR LI-ION LDO 10DFN |
| LTC4064EMSE#TRPBF | IC CHARGER BATT L-ION 4V 10-MSOP |
| LTC4065EDC#TRPBF | IC CHARGER BATT LI-ON 6-DFN |
| LTC4066EPF#TRPBF | IC USB POWER MANAGER 24-UTQFN |
| LTC4067EDE#TRPBF | IC USB POWER MANAGER 12-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4063 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Standalone Linear Li-lon Battery Charger with Thermistor Input |
| LTC4063EDD | 功能描述:IC BATT CHRGR LI-ION LDO 10DFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4063EDD#PBF | 功能描述:IC BATT CHRGR LI-ION LDO 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4063EDD#TRPBF | 功能描述:IC BATT CHRGR LI-ION LDO 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4064 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic Linear Charger for Back-Up Li-Ion Batteries |
发布紧急采购，3分钟左右您将得到回复。