- 您现在的位置：买卖IC网 > PDF目录80307 > LTC4155EUFD#TRPBF (LINEAR TECHNOLOGY CORP) POWER SUPPLY SUPPORT CKT, PQCC28 PDF资料下载
参数资料
| 型号： | LTC4155EUFD#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, PQCC28 |
| 封装： | 5 X 4 MM, 0.75 MM HEIGHT, PLASTIC, MO-220WXXX-X, QFN-28 |
| 文件页数： | 15/52页 |
| 文件大小： | 473K |
| 代理商： | LTC4155EUFD#TRPBF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
LTC4155
22
4155f
WALLSNS pins. The voltage threshold values previously
listed and specified in the Electrical Characteristics table
are valid when each input is connected to its respective
sense pin through a 3.6k resistor.
The status of the USB and WALL inputs is monitored
continuously and reported by I2C, with the option of
generating several interrupts. When all three conditions
previously listed are true, the LTC4155 will report the input
valid by asserting USBSNSGD or WALLSNSGD in the I2C
port. Optionally, if external power interrupts are enabled,
an interrupt request will be generated.
When power is applied simultaneously to both inputs,
the LTC4155 will draw power from the WALL input by
default. If the I2C PRIORITY bit is asserted, the LTC4155
will instead draw power from the USB input when both
inputs are present. The USB On-The-Go step-up regulator
delivers power only to the USB input, and the PRIOR-
ITY bit is ignored in this mode. The input current limits
USBILIM[4:0] and WALLILIM[4:0] also reset to 100mA
default mode under different criteria. In all other respects,
the two inputs are identical.
An optional capacitor may be placed between the OVGCAP
pin and GND to minimize input current disruption when
switching from one input to the other while operating at
highpowerlevels.Thecapacitormustberatedtowithstand
at least 13V and should be approximately ten times larger
than the total gate capacitance of the series NMOS power
transistors. Capacitance on this pin can also be used to
slowthegatechargingiftheapplicationrequirescontrolled
inrush current to any additional input capacitance on the
VBUS pin. If fast switching between input or inrush control
is not necessary, OVGCAP may be left unconnected.
Ifovervoltageprotectionisnotnecessaryintheapplication,
connect USBSNS to VBUS with a 3.6k resistor, as shown
in Figure 3. If the USB On-The-Go step-up regulator is
not used in the application, it is also possible to connect
WALLSNS to VBUS through 3.6k and leave USBSNS open.
100mA Linear Battery Charger Mode
The LTC4155 features a mode to support USB low power
operation.TotalinputcurrenttotheLTC4155isguaranteed
to remain below 100mA in this mode when the recom-
mended resistor is used on the CLPROG2 pin. The step-
down switching regulator does not operate in this mode.
Instead, a linear regulator provides power from VBUS to
VOUT and the battery. The linear battery charger follows
the same constant-current/constant-voltage algorithm as
the switching regulator, but regulates input current rather
than battery charge current. The voltage on the CLPROG2
pin represents the input current in this mode, using the
expression:
IVBUS =
VCLPROG2
RCLPROG2
77
( )
Battery charge current is represented by the voltage on
the PROG pin, but it is not regulated in this mode.
ICHRG =
VPROG
RPROG
1000
(
)
VOUTwillgenerallybeveryclosetothebatteryvoltagewhen
the battery charger is enabled, except when the battery
voltage is very low, the LTC4155 will increase the imped-
ance between VOUT and BATSNS to facilitate instant-on
operation. If the system load plus battery charge current
exceeds the available input current, battery charge current
will be sacrificed to give priority to the load. If the system
load alone exceeds the available input current, VOUT must
fall to the battery voltage so that the battery may provide
the supplemental current.
The battery will charge to the float voltage specified by
the I2C setting VFLOAT[1:0]. See Table 12.
When the battery charger is disabled or terminated, VOUT
will be regulated to 4.35V.
OPERATION
VBUS
TO POWER
INPUT
OVGCAP
USBGT
USBSNS
WALLGT
LTC4155
WALLSNS
4155 F03
R1
Figure 3. No Overvoltage Protection
相关PDF资料 |
PDF描述 |
|---|---|
| LM4040BIZ-5.0AMMOPACK | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 5 V, PBCY3 |
| L296VH | 4 A SWITCHING REGULATOR, 200 kHz SWITCHING FREQ-MAX, PZFM15 |
| LM9140BYM-2.5 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, PDSO8 |
| LK5540-7ERD0TB1 | 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
| LT1072IK | 1.25 A SWITCHING REGULATOR, 40 kHz SWITCHING FREQ-MAX, MBFM2 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4155IUFD#PBF | 功能描述:IC I2C POWER MANAGER DUAL 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4155IUFD#TRPBF | 功能描述:IC I2C POWER MANAGER DUAL 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4156EUFD#PBF | 功能描述:IC POWER LI-ION CHARGER 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:* 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4156EUFD#TRPBF | 功能描述:IC POWER LI-ION CHARGER 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4156IUFD#PBF | 功能描述:IC POWER LI-ION CHARGER 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:* 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
发布紧急采购，3分钟左右您将得到回复。