- 您现在的位置：买卖IC网 > PDF目录80307 > LTC4155EUFD#TRPBF (LINEAR TECHNOLOGY CORP) POWER SUPPLY SUPPORT CKT, PQCC28 PDF资料下载
参数资料
| 型号： | LTC4155EUFD#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, PQCC28 |
| 封装： | 5 X 4 MM, 0.75 MM HEIGHT, PLASTIC, MO-220WXXX-X, QFN-28 |
| 文件页数： | 4/52页 |
| 文件大小： | 473K |
| 代理商： | LTC4155EUFD#TRPBF |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
LTC4155
12
4155f
PIN FUNCTIONS
SDA (Pin 1): Data Input/Output for the I2C Serial Port.
The I2C input levels are scaled with respect to DVCC for
I2C compliance.
DVCC (Pin 2): Logic Supply for the I2C Serial Port. DVCC
sets the reference level of the SDA and SCL pins for I2C
compliance. It should be connected to the same power
supply used to power the I2C pull-up resistors.
IRQ (Pin 3): Open-Drain Interrupt Output. The IRQ pin
can be used to generate an interrupt due to a variety of
maskable status change events within the LTC4155.
ID (Pin 4): USB A-Device Detection Pin. When wired to
a mini- or micro-USB connector, the ID pin detects when
the “A” side of a mini or micro-USB cable is connected
to the product. If the ID pin is pulled down, and the
LOCKOUT_ID_PIN bit is not set in the I2C port, the switch-
ing PowerPath operates in reverse providing USB power
to the VBUS pin from the battery. USB On-The-Go power
can only be delivered from the USB multiplexer path.
CLPROG1 (Pin 5): Primary VBUS Current Limit Program-
ming Pin. A resistor from CLPROG1 to ground determines
theupperlimitofthecurrentdrawnfromtheVBUSpinwhen
CLPROG1 is selected. A precise measure of VBUS current,
hCLPROG1–1, is sent to the CLPROG1 pin. The switching
regulatorincreasespowerdeliveryuntilCLPROG1reaches
1.2V. Therefore, the current drawn from VBUS will be lim-
ited to an amount given by the 1.2V reference voltage,
hCLPROG1 and RCLPROG1.
Typically CLPROG1 is used to override the USB compliant
input current control pin, CLPROG2, in applications where
USB compliance is not a requirement. This would be use-
ful for applications that use a dedicated wall adapter and
would rather not be limited to the 500mW start-up value
required by USB specifications. If USB compliance is a
requirement at start-up, CLPROG1 should be connected
to CLPROG2 and a single resistor should be used. See
the CLPROG2 pin description.
In USB noncompliant designs, the user is encouraged to
use an RCLPROG1 value that best suits their application
for start-up current limit. See the Operation section for
more details.
CLPROG2 (Pin 6): Secondary VBUS Current Limit Pro-
gram Pin. CLPROG2 controls the VBUS current limit when
either selected via I2C command or when CLPROG1 and
CLPROG2 are shorted together. When selected, a resistor
from CLPROG2 to ground determines the upper limit of
the current drawn from the VBUS pin. Like CLPROG1, a
precise fraction of VBUS current, hCLPROG2–1, is sent to the
CLPROG2 pin. The switching regulator increases power
delivery until CLPROG2 reaches 1.2V. Therefore, the cur-
rent drawn from VBUS will be limited to an amount given
by the 1.2V reference voltage, hCLPROG2 and RCLPROG2.
ThereareamultitudeofratiosforhCLPROG2availablebyI2C
control, three of which correspond to the 100mA, 500mA
and 900mA USB specifications. CLPROG2 is also used to
regulatemaximuminputcurrentintheUSBsuspendmode
and maximum output current in USB On-The-Go mode.
IfCLPROG1andCLPROG2areshortedtogetherattheonset
of available input power, the LTC4155 selects CLPROG2 in
the 100mA USB mode to limit input current. This ensures
USB compliance if so desired. For USB compliance in all
modes, the user is encouraged to make RCLPROG2 equal
to the value declared in the specification table.
WALLSNS (Pin 7): Highest Priority Multiplexer Input and
Overvoltage Protection Sense Input. WALLSNS should be
connected through a 3.6k resistor to a high priority input
power connector and one drain of two source-connected
N-channel MOSFET pass transistors. When voltage is
detected on WALLSNS, it draws a small amount of current
to power a charge pump which then provides gate drive to
WALLGT to energize the external transistors. If the input
voltage exceeds VOVLO, WALLGT will be pulled to GND
to disable the pass transistors and protect the LTC4155
from high voltage.
USBSNS (Pin 8): Lowest Priority Multiplexer Input and
Overvoltage Protection Sense Input. USBSNS should be
connected through a 3.6k resistor to a low priority input
power connector and one drain of two source-connected
N-channel MOSFET pass transistors. When voltage is
detected on USBSNS, and no voltage is detected on
WALLSNS, USBSNS draws a small amount of current to
power a charge pump which then provides gate drive to
相关PDF资料 |
PDF描述 |
|---|---|
| LM4040BIZ-5.0AMMOPACK | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 5 V, PBCY3 |
| L296VH | 4 A SWITCHING REGULATOR, 200 kHz SWITCHING FREQ-MAX, PZFM15 |
| LM9140BYM-2.5 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, PDSO8 |
| LK5540-7ERD0TB1 | 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
| LT1072IK | 1.25 A SWITCHING REGULATOR, 40 kHz SWITCHING FREQ-MAX, MBFM2 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4155IUFD#PBF | 功能描述:IC I2C POWER MANAGER DUAL 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4155IUFD#TRPBF | 功能描述:IC I2C POWER MANAGER DUAL 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4156EUFD#PBF | 功能描述:IC POWER LI-ION CHARGER 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:* 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4156EUFD#TRPBF | 功能描述:IC POWER LI-ION CHARGER 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4156IUFD#PBF | 功能描述:IC POWER LI-ION CHARGER 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:* 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
发布紧急采购，3分钟左右您将得到回复。