- 您现在的位置：买卖IC网 > PDF目录80307 > LTC4155EUFD#TRPBF (LINEAR TECHNOLOGY CORP) POWER SUPPLY SUPPORT CKT, PQCC28 PDF资料下载
参数资料
| 型号： | LTC4155EUFD#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, PQCC28 |
| 封装： | 5 X 4 MM, 0.75 MM HEIGHT, PLASTIC, MO-220WXXX-X, QFN-28 |
| 文件页数： | 18/52页 |
| 文件大小： | 473K |
| 代理商： | LTC4155EUFD#TRPBF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
LTC4155
25
4155f
Byte Format
Each frame sent to or received from the LTC4155 must
be eight bits long, followed by an extra clock cycle for the
acknowledge bit. The data should be sent to the LTC4155
most significant bit (MSB) first.
Master and Slave Transmitters and Receivers
Devices connected to an I2C bus may be classified as
either master or slave. A typical bus is composed of one
or more master devices and a number of slave devices.
Some devices are capable of acting as either a master or
a slave, but they may not change roles while a transaction
is in progress.
The transmitter/receiver relationship is distinct from that
of master and slave. The transmitter is responsible for
control of the SDA line during the eight bit data portion
of each frame. The receiver is responsible for control of
SDA during the ninth and final acknowledge clock cycle
of each frame.
All transactions are initiated by the master with a START
or repeat START condition. The master controls the active
(falling) edge of each clock pulse on SCL, regardless of its
status as transmitter or receiver. The slave device never
brings SCL LOW, but may extend the SCL LOW time to
implement clock stretching if necessary. The LTC4155
does not clock stretch and will never hold SCL LOW under
any circumstance.
The master device begins each I2C transaction as the
transmitter and the slave device begins each transaction
as the receiver. For bus write operations, the master acts
as the transmitter and the slave acts as receiver for the
duration of the transaction. For bus read operations, the
masterandslaveexchangetransmit/receiverolesfollowing
the address frame for the remainder of the transaction.
Acknowledge
The acknowledge signal (ACK) is used for handshaking
between the transmitter and receiver. When the LTC4155
is written to, it acknowledges its write address as well as
the subsequent data bytes as a slave receiver. When it is
read from, the LTC4155 acknowledges its read address
as a slave receiver. The LTC4155 then changes to a slave
transmitterandthemasterreceivermayoptionallyacknowl-
edge receipt of the following data byte from the LTC4155.
Theacknowledgerelatedclockpulseisalwaysgeneratedby
the bus master. The transmitter (master or slave) releases
the SDA line (HIGH) during the acknowledge clock cycle.
The receiver (slave or master) pulls down the SDA line
during the acknowledge clock pulse so that it is a stable
LOW during the HIGH period of this clock pulse.
When the LTC4155 is read from, it releases the SDA line
after the eighth data bit so that the master may acknowl-
edge receipt of the data. The I2C specification calls for a
not acknowledge (NACK) by the master receiver following
the last data byte during a read transaction. Upon receipt
of the NACK, the slave transmitter is instructed to release
control of the bus. Because the LTC4155 only transmits
one byte of data under any circumstance, a master ac-
knowledging or not acknowledging the data sent by the
LTC4155 has no consequence. The LTC4155 will release
the bus in either case.
Slave Address
The LTC4155 responds to a 7-bit address which has been
factory programmed to 0b0001001[R/W]. The LSB of
the address byte, known as the read/write bit, should be
0 when writing data to the LTC4155, and 1 when reading
data from it. Considering the address an 8-bit word, then
the write address is 0x12, and the read address is 0x13.
The LTC4155 will acknowledge both its read and write
addresses.
Sub Addressed Access
The LTC4155 has four command registers for control
input and three status registers for status reporting. They
are accessed by the I2C port via a sub addressed pointer
system where each sub address value points to one of
the seven control or status registers within the LTC4155.
The sub address pointer is always the first byte written
immediately following the LTC4155 write address dur-
ing bus write operations. The sub address pointer value
persists after the bus write operation and will determine
which data byte is returned by the LTC4155 during any
OPERATION
相关PDF资料 |
PDF描述 |
|---|---|
| LM4040BIZ-5.0AMMOPACK | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 5 V, PBCY3 |
| L296VH | 4 A SWITCHING REGULATOR, 200 kHz SWITCHING FREQ-MAX, PZFM15 |
| LM9140BYM-2.5 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, PDSO8 |
| LK5540-7ERD0TB1 | 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
| LT1072IK | 1.25 A SWITCHING REGULATOR, 40 kHz SWITCHING FREQ-MAX, MBFM2 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4155IUFD#PBF | 功能描述:IC I2C POWER MANAGER DUAL 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4155IUFD#TRPBF | 功能描述:IC I2C POWER MANAGER DUAL 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4156EUFD#PBF | 功能描述:IC POWER LI-ION CHARGER 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:* 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4156EUFD#TRPBF | 功能描述:IC POWER LI-ION CHARGER 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4156IUFD#PBF | 功能描述:IC POWER LI-ION CHARGER 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:* 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
发布紧急采购，3分钟左右您将得到回复。