- 您现在的位置：买卖IC网 > PDF目录79689 > LTC4160EUDC#TRPBF (LINEAR TECHNOLOGY CORP) POWER SUPPLY MANAGEMENT CKT, PQCC20 PDF资料下载
参数资料
| 型号： | LTC4160EUDC#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | POWER SUPPLY MANAGEMENT CKT, PQCC20 |
| 封装： | 3 X 4 MM, 0.75 MM HEIGHT, LEAD FREE, PLASTIC, QFN-20 |
| 文件页数： | 13/32页 |
| 文件大小： | 422K |
| 代理商： | LTC4160EUDC#TRPBF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC4160/LTC4160-1
20
41601fa
OPERATION
switching regulator is in On-The-Go mode. When a short
circuit condition is detected, FAULT will go low-Z. The
ENOTG or VBUSGD pins can be used to determine which
faulthasoccurred.IfENOTGorVBUSGDislowwhenFAULT
went low, then a bad battery fault has occurred. If either
pin is high, then a short circuit on VBUS has occurred.
NTC Thermistor
The battery temperature is measured by placing a nega-
tive temperature coefficient (NTC) thermistor close to the
battery pack.
To use this feature connect the NTC thermistor, RNTC, be-
tween the NTC pin and ground and a bias resistor, RNOM,
from NTCBIAS to NTC. RNOM should be a 1% 200ppm
resistor with a value equal to the value of the chosen NTC
thermistor at 25°C (R25).
The LTC4160/LTC4160-1 will pause charging when the
resistance of the NTC thermistor drops to 0.54 times the
value of R25 or approximately 54k for a 100k thermis-
tor. For a Vishay Curve 1 thermistor, this corresponds to
approximately 40°C. If the battery charger is in constant-
voltage (float) mode, the safety timer also pauses until the
thermistor indicates a return to a valid temperature. As the
temperature drops, the resistance of the NTC thermistor
rises. The LTC4160/LTC4160-1 are also designed to pause
charging when the value of the NTC thermistor increases
to 3.25 times the value of R25. For a Vishay Curve 1
100k thermistor, this resistance, 325k, corresponds to
approximately 0°C. The hot and cold comparators each
have approximately 3°C of hysteresis to prevent oscilla-
tion about the trip point. Grounding the NTC pin disables
all NTC functionality.
Thermal Regulation
To prevent thermal damage to the LTC4160/LTC4160-1 or
surrounding components, an internal thermal feedback
loop will automatically decrease the programmed charge
current if the die temperature rises to 105°C. This thermal
regulation technique protects the LTC4160/LTC4160-1
from excessive temperature due to high power operation
or high ambient thermal conditions, and allows the user
to push the limits of the power handling capability with
a given circuit board design. The benefit of the LTC4160/
LTC4160-1 thermal regulation loop is that charge current
can be set according to actual conditions rather than
worst-case conditions for a given application with the
assurance that the charger will automatically reduce the
current in worst-case conditions.
Overvoltage Protection
The LTC4160/LTC4160-1 can protect themselves from the
inadvertent application of excessive voltage to VBUS with
just two external components: an N-channel MOSFET and
a 6.2k resistor. The maximum safe overvoltage magnitude
will be determined by the choice of the external MOSFET
and its associated drain breakdown voltage.
The overvoltage protection circuit consists of two pins.
The first, OVSENS, is used to measure the externally ap-
plied voltage through an external resistor. The second,
OVGATE, is an output used to drive the gate pin of the
external MOSFET. When OVSENS is below 6V, an inter-
nal charge pump will drive OVGATE to approximately
1.88 OVSENS. This will enhance the N-channel MOSFET
and provide a low impedance connection to VBUS which
will, in turn, power the LTC4160/LTC4160-1. If OVSENS
should rise above 6V due to a fault or the use of an in-
correct wall adapter, OVGATE will be pulled to GND. This
disables the external MOSFET and protects downstream
circuitry. When the voltage drops below 6V again, the
external MOSFET will be re-enabled.
The charge pump output on OVGATE has limited output
drive capability. Care must be taken to avoid leakage on
this pin as it may adversely affect operation.
SeetheApplicationsInformationsectionforresistorpower
dissipation rating calculations, a table of recommended
components, and reverse-voltage protection.
Shutdown Mode
The USB switching regulator is enabled whenever VBUS is
above VUVLO and the LTC4160/LTC4160-1 are not in USB
suspend mode.
The ideal diode(s) are enabled at all times and cannot be
disabled.
相关PDF资料 |
PDF描述 |
|---|---|
| LM385BZ-1.2X | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.235 V, PBCY3 |
| LES008ZD28N | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| LFD150S | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| LT3575EFE#TRPBF | 4.2 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| LM9140BXM-5.0 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 5 V, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4210 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Supply Hot Swap Controller for Advanced Mezzanine Card |
| LTC4210-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Hot Swap Controller in 6-Lead SOT-23 Package |
| LTC42101CS6 | 制造商:Linear Technology 功能描述: |
| LTC4210-1CS6 | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 16.5V 6-Pin TSOT-23 |
| LTC4210-1CS6#PBF | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 16.5V 6-Pin TSOT-23 制造商:Linear Technology 功能描述:IC HOT SWAP CONT 制造商:Linear Technology 功能描述:HOT SWAP CNTRL 16.5VIN 6SOT23 制造商:Linear Technology 功能描述:HOT SWAP, CNTRL, 16.5VIN, 6SOT23 制造商:Linear Technology 功能描述:IC, HOT SWAP CONT; Controller Applications:Hot Board Insertion, Electronic Circuit Breaker, Industrial High Side Switch; Input Voltage:16.5V; Internal Switch:Yes; Supply Voltage Min:2.7V; Supply Voltage Max:16.5V; No. of Pins:6 ;RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。