- 您现在的位置：买卖IC网 > PDF目录22108 > LTC4222IUH#TRPBF (Linear Technology)IC CTRLR DUAL HOT SWAP 32-QFN PDF资料下载
参数资料
| 型号： | LTC4222IUH#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/32页 |
| 文件大小： | 339K |
| 描述： | IC CTRLR DUAL HOT SWAP 32-QFN |
| 标准包装： | 2,500 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 2.9 V ~ 29 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC4222
11
4222fb
OPERATION
The LTC4222 is designed to turn two supply voltages
on and off in a controlled manner, allowing boards to be
safely inserted or removed from a live backplane. During
normal operation, the charge pump and gate drivers turn
on external N-channel MOSFET gates to pass power to
the loads. The gate driver circuits use a charge pump that
derives its power from the V
DD1
or V
DD2
pin, whichever is
higher. Also included in the gate driver circuits are internal
6.5V GATE-to-SOURCE clamps to protect the oxide of
logic-level MOSFETs. During start-up the inrush currents
are tightly controlled by using current limit foldback, soft-
start dI/dt limiting and output dI/dt limiting. The LTC4222
is capable of controlling both channels independently, or
coupling control signals so that both channels start up
and turn off together.
The current sense (CS) amplifiers monitor the load cur-
rents using the difference between the SENSE
+
(V
DD
for
QFN) and SENSE
pin voltages. A CS amplifier limits the
current in the load by pulling back on the GATE-to-SOURCE
voltage in an active control loop when the sense voltage
exceeds the commanded value. The CS amplifiers require
20礎 input bias current from both the SENSE
+
and the
SENSE
pins.
A short circuit on an output to ground results in excessive
power dissipation during active current limiting. To limit this
power, the corresponding CS amplifier regulates the voltage
between the SENSE
+
and SENSE
pins at 150mV .
If an overcurrent condition persists, the internal circuit
breaker (CB) registers a fault when the sense voltage
exceeds 50mV for more than 20祍. This indicates to
the logic that it is time to turn off the GATE to prevent
overheating. At this point the TIMER capacitor starts to
discharge with the 2礎 current source until the voltage
drops below 0.2V (comparator TM1) which tells the logic
that the pass transistor has cooled and it is safe to turn
on again if overcurrent auto-retry is enabled. If the TIMER
pin is tied to INTV
CC
, the cool-down time defaults to
5 seconds using an internal system timer.
The output voltages are monitored using the FB resistive
divider and the power good (PG) comparators to determine
when output voltages are acceptable for the loads. The
power good conditions are signaled by the GPIO1 and
GPIO2 pins using open-drain pull-down transistors. The
GPIO pins may also be independently configured to signal
power bad, or as general purpose inputs (GP comparators),
or general purpose open-drain outputs.
The Functional Diagram shows the monitoring blocks of
the LTC4222. The group of comparators on the left side
includes the undervoltage (UV), overvoltage (OV), reset
(RST), enable (EN) and on (ON) comparators for chan-
nel 1 or 2. These comparators determine if the external
conditions are valid prior to turning on their correspond-
ing GATE. The two undervoltage lockout circuits, UVLO1
and UVLO2, validate the input supplies and the internally
generated 3.3V supply, INTV
CC
. UVLO2 also generates
the power-up initialization to the logic circuits as INTV
CC
crosses this rising threshold.
The CONFIG pin is used to select the desired start-up
behavior of the LTC4222. When the CONFIG pin is low,
both channels will start up and turn off simultaneously
and a fault on either channel will result in both channels
turning off, or prevent both channels from starting up.
t
SU, DAT
t
SU, STO
t
SU, STA
t
BUF
t
HD, STA
t
SP
t
SP
t
HD, DATO,
t
HD, DATI
t
HD, STA
START
CONDITION
STOP
CONDITION
REPEATED START
CONDITION
START
CONDITION
4222 TD01
SDAI/SDAO
SCL
TIMING DIAGRAM
相关PDF资料 |
PDF描述 |
|---|---|
| RMA35DRMT | CONN EDGECARD 70POS .125 SQ WW |
| TOP243PN | IC OFFLINE SWIT OVP UVLO HV 8DIP |
| LTC4222IG#TRPBF | IC CTRLR DUAL HOT SWAP 36-SSOP |
| TOP257MN | IC OFFLINE SWIT PROG OVP 10CSDIP |
| GMM43DRKI | CONN EDGECARD 86POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4223 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Ideal Diode and Hot Swap Controller |
| LTC4223-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Supply Hot Swap Controller for Advanced Mezzanine Card |
| LTC4223-2 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Supply Hot Swap Controller for Advanced Mezzanine Card |
| LTC4223CDHD-1#PBF | 功能描述:IC CNTRLR HOT SWAP DUAL 16-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LTC4223CDHD-1#TRPBF | 功能描述:IC CNTRLR HOT SWAP DUAL 16-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。