- 您现在的位置：买卖IC网 > PDF目录22108 > LTC4222IUH#TRPBF (Linear Technology)IC CTRLR DUAL HOT SWAP 32-QFN PDF资料下载
参数资料
| 型号： | LTC4222IUH#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 20/32页 |
| 文件大小： | 339K |
| 描述： | IC CTRLR DUAL HOT SWAP 32-QFN |
| 标准包装： | 2,500 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 2.9 V ~ 29 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC4222
20
4222fb
APPLICATIONS INFORMATION
The address is set with the help of Table 1, which indi-
cates binary address 1000111 corresponds to address
4. Address 4 is set by setting ADR2 low, ADR1 open and
ADR0 high.
Next the value of R5 and R6 are chosen to be the default
values 10?and 15k?as discussed previously.
In addition a 0.1礔 ceramic bypass capacitor is placed on
the INTV
CC
pin.
Layout Considerations
To achieve accurate current sensing, a Kelvin connection
is required. The minimum trace width for 1oz copper
foil is 0.02" per amp to make sure the trace stays at a
reasonable temperature. Using 0.03" per amp or wider
is recommended. Note that 1oz copper exhibits a sheet
resistance of about 530旦. Small resistances add up
quickly in high current applications. To improve noise
immunity, put the resistive dividers to the UV , OV and FB
pins close to the device and keep traces to V
DD
and GND
short. It is also important to put the bypass capacitor for
the INTV
CC
pin, C3, as close as possible between INTV
CC
and GND. 0.1礔 capacitors from the UV pins (and OV pins
through resistor R2) to GND also helps reject supply noise.
Figure 5 shows a layout that addresses these issues. Note
that surge suppressor, Z1 is placed between supply and
ground using wide traces.
Digital Interface
The LTC4222 communicates with a bus master using a
2-wire interface compatible with I
2
C Bus and SMBus, an
I
2
C extension for low power devices. The LTC4222 is a
read-write slave device and supports SMBus bus Read
Byte, Write Byte, Read Word and Write Word commands.
A complete list of the resistors of the LTC4222 is shown
in Table 2. The second word in a Read Word command is
the contents of the subsequent 8-bit register. The second
word in a Write Word command is ignored. Data formats
for these commands are shown in Figures 6 to 11.
The LTC4222 interface also features a 25ms timeout feature
to prevent the bus being stuck low if a communication
error occurs. If either the SCL or SDA lines remain low
for more than 25ms the LTC4222 will reset its interface
and release the SDAO pin, freeing the bus to resume
communication.
The LTC4222 also features PMBus compatibility, the in-
terface will not acknowledge unsupported commands and
the internal addresses are in the manufacturer specified
address space under the PMBus specification.
START and STOP Conditions
When the bus is idle, both SCL and SDA are high. A bus
master signals the beginning of a transmission with a start
condition by transitioning SDA from high to low while SCL
is high, as shown in Figure 6. When the master has finished
communicating with the slave, it issues a STOP condition
by transitioning SDA from low to high while SCL is high.
The bus is then free for another transmission.
I
2
C Device Addressing
Twenty seven distinct bus addresses are available using
three 3-state address pins, ADR0, ADR1 and ADR2. Table 1
shows the correspondence between pin states and ad-
dresses. In addition, the LTC4222 responds to two special
addresses. Address (1100 0110) is a mass write address
that writes to all LTC4222s, regardless of their individual
address settings. Mass write can be disabled by setting
register bit 4 in the CONTROL register of channel 2 to zero.
Address (0001 100) is the SMBus Alert Response Address.
If the LTC4222 is pulling low on the ALERT pin due to an
Figure 5. Recommended Layout
SS
CONFIG
INTV
CC
GND
LTC4222UHD
4222 F05
VIAS TO
GROUND
PLANE
VIA TO
GROUND
PLANE
SENSE RESISTOR R
S
I
LOAD
C
SS
C3
R2
R3
C
F
Z1
R1
相关PDF资料 |
PDF描述 |
|---|---|
| RMA35DRMT | CONN EDGECARD 70POS .125 SQ WW |
| TOP243PN | IC OFFLINE SWIT OVP UVLO HV 8DIP |
| LTC4222IG#TRPBF | IC CTRLR DUAL HOT SWAP 36-SSOP |
| TOP257MN | IC OFFLINE SWIT PROG OVP 10CSDIP |
| GMM43DRKI | CONN EDGECARD 86POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4223 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Ideal Diode and Hot Swap Controller |
| LTC4223-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Supply Hot Swap Controller for Advanced Mezzanine Card |
| LTC4223-2 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Supply Hot Swap Controller for Advanced Mezzanine Card |
| LTC4223CDHD-1#PBF | 功能描述:IC CNTRLR HOT SWAP DUAL 16-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LTC4223CDHD-1#TRPBF | 功能描述:IC CNTRLR HOT SWAP DUAL 16-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。