- 您现在的位置：买卖IC网 > PDF目录20107 > LTC4225IUFD-2#PBF (Linear Technology)IC CONTROLLER HOT SWAP 24-QFN PDF资料下载
参数资料
| 型号： | LTC4225IUFD-2#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/24页 |
| 文件大小： | 346K |
| 描述： | IC CONTROLLER HOT SWAP 24-QFN |
| 标准包装： | 73 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电流限制： | 可调 |
| 电源电压： | 2.9 V ~ 18 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 供应商设备封装： | 24-QFN（5x4） |
| 包装： | 管件 |
LTC4225-1/LTC4225-2
9
422512f
operaTion
The LTC4225 functions as an ideal diode with inrush cur-
rent limiting and overcurrent protection by controlling
two external back-to-back N-channel MOSFETs (M
D
and
M
H
) on a supply path. This allows boards to be safely
inserted and removed in systems with a backplane pow-
ered by redundant supplies, such as 礣CA applications.
The LTC4225 has two separate ideal diode and Hot Swap
controllers, each providing independent control for the
two input supplies.
When the LTC4225 is first powered up, the gates of the
back-to-back MOSFETs are held low, keeping them off.
The gate drive amplifier (GA1, GA2) monitors the voltage
between the IN and OUT pins and drives the DGATE pin.
The amplifier quickly pulls up the DGATE pin, turning
on the MOSFET for ideal diode control, when it senses
a large forward voltage drop. The stored charge in an
external capacitor connected between the CPO and IN
pins provides the charge needed to quickly turn on the
ideal diode MOSFET . An internal charge pump charges up
this capacitor at device power-up. The DGATE pin sources
current from the CPO pin and sinks current into the IN
and GND pins.
Pulling the ON pin high and the EN pin low initiates a
100ms debounce timing cycle. After this timing cycle, a
10礎 current source from the charge pump ramps up the
HGATE pin. When the Hot Swap MOSFET turns on, the
inrush current is limited at a level set by an external sense
resistor (R
S
) connected between the IN and SENSE pins.
An active current limit amplifier (A1, A2) servos the gate
of the MOSFET to 65mV across the current sense resistor.
Inrush current can be further reduced, if desired, by add-
ing a capacitor from HGATE to GND. When the MOSFET s
gate overdrive (HGATE to OUT voltage) exceeds 4.2V , the
PWRGD pin pulls low.
When both of the MOSFETs are turned on, the gate drive
amplifier controls DGATE to servo the forward voltage drop
(V
IN
V
OUT
) across the sense resistor and the back-to-back
MOSFETs to 25mV . If the load current causes more than
25mV of voltage drop, the gate voltage rises to enhance
the MOSFET used for ideal diode control. For large output
currents, the MOSFET s gate is driven fully on and the
voltage drop across the MOSFETs is equal to the sum of
the I
LOAD
" R
DS(ON)
of the two MOSFETs in series.
In the case of an input supply short circuit when the
MOSFETs are conducting, a large reverse current starts
fowing from the load towards the input. The gate drive
amplifier detects this failure condition as soon as it ap-
pears and turns off the ideal diode MOSFET by pulling
down the DGATE pin.
In the case where an overcurrent fault occurs on the sup-
ply output, the current is limited to 65mV/R
S
. After a fault
flter delay set by 100礎 charging the TMR pin capacitor,
the circuit breaker trips and pulls the HGATE pin low, turn-
ing off the Hot Swap MOSFET . Only the supply at fault is
affected, with the corresponding FAULT pin latched low.
At this point, the DGATE pin continues to pull high and
keeps the ideal diode MOSFET on.
Internal clamps limit both the DGATE to IN and CPO to IN
voltages to 12V . The same clamp also limits the CPO and
DGATE pins to a diode voltage below the IN pin. Another
internal clamp limits the HGATE to OUT voltage to 12V
and also clamps the HGATE pin to a diode voltage below
the OUT pin.
Power to the LTC4225 is supplied from either the IN or
OUT pins, through an internal diode-OR circuit to a low
dropout regulator (LDO). That LDO generates a 5V supply
at the INTV
CC
pin and powers the LTC4225s internal low
voltage circuitry.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-27P-CX | CONVERTER MOD DC/DC 13.8V 75W |
| T86C155K035EAAS | CAP TANT 1.5UF 35V 10% 2312 |
| VI-27N-CX | CONVERTER MOD DC/DC 18.5V 75W |
| CENB1010A1803F01 | POWER SUPPLY EXT 12W 18V @ 0.67A |
| TCJC336M010R0100 | CAP TANT 33UF 10V 20% 2312 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4226 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Wide Operating Range Dual Hot Swap Controller Fast Response Limits Peak Fault Current |
| LTC4226CMS-1#PBF | 制造商:Linear Technology 功能描述:Hot Swap Controller 2-CH 44V 16-Pin MSOP 制造商:Linear Technology 功能描述:IC HOT SWAP CONTROL DUAL 16MSOP |
| LTC4226CMS-1#TRPBF | 制造商:Linear Technology 功能描述:Hot Swap Controller 2-CH 44V 16-Pin MSOP T/R 制造商:Linear Technology 功能描述:IC HOT SWAP CONTROL DUAL 16MSOP |
| LTC4226CMS-2#PBF | 制造商:Linear Technology 功能描述:Hot Swap Controller 2-CH 44V 16-Pin MSOP 制造商:Linear Technology 功能描述:IC HOT SWAP CONTROL DUAL 16MSOP |
| LTC4226CMS-2#TRPBF | 制造商:Linear Technology 功能描述:Hot Swap Controller 2-CH 44V 16-Pin MSOP T/R 制造商:Linear Technology 功能描述:IC HOT SWAP CONTROL DUAL 16MSOP |
发布紧急采购，3分钟左右您将得到回复。