- 您现在的位置：买卖IC网 > PDF目录11577 > LTC4267CGN#TRPBF (Linear Technology)IC POE 802.3AF INTERFACE 16SSOP PDF资料下载
参数资料
| 型号： | LTC4267CGN#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 16/32页 |
| 文件大小： | 0K |
| 描述： | IC POE 802.3AF INTERFACE 16SSOP |
| 标准包装： | 2,500 |
| 控制器类型： | 以太网供电控制器（POE） |
| 接口： | IEEE 802.3af |
| 电流 - 电源： | 3mA |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 带卷 (TR) |
| 相关产品： | 732-2437-6-ND - TRANS FLYBACK POE 40UH SMD 732-2436-6-ND - TRANS FLYBACK POE 35UH SMD 732-2435-6-ND - TRANS FLYBACK POE 127UH SMD 732-2434-6-ND - TRANS FLYBACK POE 127UH SMD 732-2433-6-ND - TRANS FLYBACK POE 127UH SMD 732-2432-6-ND - TRANS FLYBACK POE 127UH SMD 732-2431-6-ND - TRANS FLYBACK POE 127UH SMD 732-2430-6-ND - TRANS FLYBACK POE 127UH SMD 732-2437-1-ND - TRANS FLYBACK POE 40UH SMD 732-2436-1-ND - TRANS FLYBACK POE 35UH SMD 更多... |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC4267
23
4267fc
The shunt regulator can sink up to 5mA through the PVCC
pin to PGND. The values of RSTART and CPVCC must be
selected for the application to withstand the worst-case
load conditions and drop on PVCC, ensuring that the PVCC
turn-off threshold is not reached. CPVCC should be sized
sufciently to handle the switching current needed to drive
NGATE while maintaining minimum switching voltage.
actual current needed to power the LTC4267 switching
regulator goes through Q1 and PVCC sources current on
an “as-needed” basis. The static current is then limited
only to the current through RB and D1.
APPLICATIO S I FOR ATIO
WU
UU
Figure 12. Powering the LTC4267 Switching
Regulator via the Shunt Regulator
Figure 13. Powering the LTC4267 Switching
Regulator with an External Preregulator
VPORTP
PVCC
PGND
POUT
VPORTN
LTC4267
–48
FROM
PSE
RSTART
CPVCC
+
–
PGND
4267 F14
External Preregulator
The circuit in Figure 13 shows a third way to power the
LTC4267 switching regulator circuit. An external series
preregulator consists of a series pass transistor Q1, zener
diode D1, and a bias resistor RB. The preregulator holds
PVCC at 7.6V nominal, well above the maximum rated PVCC
turn-off threshold of 6.8V. Resistor RSTART momentarily
charges the PVCC node up to the PVCC turn-on threshold,
enabling the switching regulator. The voltage on CPVCC
begins to decline as the switching regulator draws its
normal supply current, which exceeds the delivery of
RSTART. After some time, the output voltage approaches
the desired value. By this time, the pass transistor Q1
catches the declining voltage on the PVCC pin, and provides
virtually all the supply current required by the LTC4267
switching regulator. CPVCC should be sized sufciently to
handle the switching current needed to drive NGATE while
maintaining minimum switching voltage.
The external preregulator has improved efciency over
the simple resistor-shunt regulator method mentioned
previously. RB can be selected so that it provides a small
current necessary to maintain the zener diode voltage and
the maximum possible base current Q1 will encounter. The
VPORTP
PVCC
PGND
POUT
VPORTN
LTC4267
–48
FROM
PSE
RSTART
CPVCC
+
–
PGND
Q1
D1
8.2V
RB
4267 F15
Compensating the Main Loop
In an isolated topology, the compensation point is typically
chosen by the components congured around the external
error amplier. Shown in Figure 14, a series RC network
is connected from the compare voltage of the error am-
plier to the error amplier output. In PD designs where
transient load response is not critical, replace RZ with a
short. The product of R2 and CC should be sufciently large
to ensure stability. When fast settling transient response
is critical, introduce a zero set by RZCC. The PD designer
must ensure that the faster settling response of the output
voltage does not compromise loop stability.
In a nonisolated design, the LTC4267 incorporates an
internal error amplier where the ITH/RUN pin serves as
a compensation point. In a similar manner, a series RC
network can be connected from ITH/RUN to PGND as
shown in Figure 15. CC and RZ are chosen for optimum
load and line transient response.
Figure 14. Main Loop Compensation for an Isolated Design
R1
R2
CC
RZ
TO OPTO-
ISOLATOR
4267 F14
VOUT
相关PDF资料 |
PDF描述 |
|---|---|
| 031-4237 | CONN BNC RCPT BULKHEAD REAR MNT |
| VI-2NJ-CV-S | CONVERTER MOD DC/DC 36V 150W |
| VI-2NF-CV-S | CONVERTER MOD DC/DC 72V 150W |
| 083-59SP | CONN PLUG UHF CRIMP RG59,140 |
| VI-2N4-CV-S | CONVERTER MOD DC/DC 48V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4267IDHC | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH -57V 16-Pin DFN EP |
| LTC4267IDHC#PBF | 功能描述:IC POE 802.3AF INTERFACE 16-DFN RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC4267IDHC#TRPBF | 功能描述:IC POE 802.3AF INTERFACE 16-DFN RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC4267IDHC-1#PBF | 制造商:Linear Technology 功能描述:Bulk |
| LTC4267IDHC-3#PBF | 功能描述:IC POE 802.3AF W/REG 16-DFN RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND |
发布紧急采购，3分钟左右您将得到回复。