- 您现在的位置：买卖IC网 > PDF目录15925 > LTC691ISW#PBF (Linear Technology)IC MPU SUPERVISRY CIRCUIT 16SOIC PDF资料下载
参数资料
| 型号： | LTC691ISW#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/20页 |
| 文件大小： | 0K |
| 描述： | IC MPU SUPERVISRY CIRCUIT 16SOIC |
| 标准包装： | 47 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 高有效/低有效 |
| 复位超时： | 最小为 35 ms |
| 电压 - 阀值： | 4.65V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 管件 |
LTC690/LTC691
LTC694/LTC695
APPLICATIONS INFORMATION
V HYSTERESIS = 5V
= 850mV
7.5V = 1.3V ? 1 +
?
V BATT
R1
R3
R3 ≈ 5.88 R1
Choose R3 = 300k and R1 = 51k. Also select R4 = 10k
which is much smaller than R3.
? 51k (5V ? 1.3V) 51k ?
?
? R2 1.3V (310k) ?
3V
R1
1M
R2
1M
R L
20K
PFI LTC695
5V
V CC
PFO
LTC691
CE IN
CE OUT GND
690 F10
LOW-BATTERY SIGNAL
TO μP I/O PIN
I/O PIN
R2 = 9.7kΩ, Choose nearest 5% resistor 10k and recalcu-
late V L ,
OPTIONAL TEST LOAD
V L = 1.3V ? 1 +
?
?
51k
10k
?
(5V ? 1.3V) 51k ?
1.3V (310k) ? ?
= 7.32V
Figure 10. Back-Up Battery Monitor with Optional Test Load
Watchdog Timer
V H = 1.3V ? 1 +
?
= 8.151V
= 10.7ms
? 51k 51k ?
?
? 10k 300k ?
(7.32V ? 6.25V)
100mV / ms
V HYSTERESIS = 8.151V ? 7.32V = 831mV
The 10.7ms allows enough time to execute shutdown
procedure for microprocessor and 831mV of hysteresis
would prevent PFO from going low due to the noise of V IN .
Example 2: The circuit in Figure 9 can be used to measure
the regulated 5V supply to provide early warning of power
failure. Because of variations in the PFI threshold, this
circuit requires adjustment to ensure the PFI compara-
tor trips before the reset threshold is reached. Adjust R5
such that the PFO output goes low when the V CC supply
reaches the desired level (e.g., 4.85V).
Monitoring the Status of the Battery
C3 can also monitor the status of the memory back-up
battery (Figure 10). If desired, the CE OUT can be used to
apply a test load to the battery. Since CE OUT is forced high
in battery back-up mode, the test load will not be applied
to the battery while it is in use, even if the microprocessor
is not powered.
The LTC690 family provides a watchdog timer function
to monitor the activity of the microprocessor. If the mi-
croprocessor does not toggle the Watchdog Input (WDI)
within a selected timeout period, RESET is forced to ac-
tive low for a minimum of 35ms for the LTC690/LTC691
(140ms for the LTC694/LTC695). The reset active time is
adjustable on the LTC691/LTC695. Since many systems
can not service the watchdog timer immediately after a
reset, the LTC691 and LTC695 have longer timeout period
(1.0 second minimum) right after a reset is issued. The
normal timeout period (70ms minimum) becomes effective
following the first transition of WDI after RESET is inac-
tive. The watchdog timeout period is fixed at 1.0 second
minimum on the LTC690 and LTC694. Figure 11 shows
the timing diagram of watchdog timeout period and reset
active time. The watchdog timeout period is restarted as
soon as RESET is inactive. When either a high-to-low
or low-to-high transition occurs at the WDI pin prior to
timeout, the watchdog time is reset and begins to time
out again. To ensure the watchdog time does not time
out, either a high-to-low or low-to-high transition on the
WDI pin must occur at or less than the minimum timeout
period. If the input to the WDI pin remains either high or
low, reset pulses will be issued every 1.6 seconds typically.
The watchdog time can be deactivated by floating the WDI
pin. The timer is also disabled when V CC falls below the
reset voltage threshold or V BATT .
690ff
For more information www.linear.com/690
13
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6427PRUR+T | IC MONITOR BAT LP SOT23-3 |
| ADM1067ASU | IC SUPERVISOR/SEQUENCER 48-TQFP |
| 25PK10000MGC18X35.5 | CAP ALUM 10000UF 25V 20% RADIAL |
| SRR4028-3R3Y | INDUCTOR POWER 3.3UH 2.15A 4028 |
| SRR4028-181Y | INDUCTOR POWER 180UH 0.39A 4028 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC692 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Microprocessor Supervisory Circuits |
| LTC692_09 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Microprocessor Supervisory Circuits |
| LTC692C | 制造商:LINER 制造商全称:Linear Technology 功能描述:Microprocessor Supervisory Circuits |
| LTC692CN8 | 功能描述:IC MPU SUPERVISORY CIRCUIT 8-DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC692CN8#PBF | 功能描述:IC MPU SUPERVISORY CIRCUIT 8-DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
发布紧急采购，3分钟左右您将得到回复。