- 您现在的位置：买卖IC网 > PDF目录9517 > LTC6992CDCB-4#TRMPBF (Linear Technology)IC OSC SILICON 1MHZ 6-DFN PDF资料下载
参数资料
| 型号： | LTC6992CDCB-4#TRMPBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/34页 |
| 文件大小： | 0K |
| 描述： | IC OSC SILICON 1MHZ 6-DFN |
| 产品培训模块： | TimerBlox Family Timing Devices |
| 产品目录绘图： | LTC699_DFN |
| 特色产品： | LTC?6992 TimerBlox? TimerBlox? |
| 标准包装： | 1 |
| 系列： | TimerBlox® |
| 类型： | 振荡器 - 硅 |
| 频率： | 3.81Hz ~ 1MHz |
| 电源电压： | 2.25 V ~ 5.5 V |
| 电流 - 电源： | 365µA |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 6-WFDFN 裸露焊盘 |
| 包装： | 标准包装 |
| 供应商设备封装： | 6-DFN-EP（2x3） |
| 安装类型： | 表面贴装 |
| 配用： | DC1562A-C-ND - BOARD EVAL LTC6992-1 |
| 其它名称： | LTC6992CDCB-4#TRMPBFDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
LTC6992-1/LTC6992-2/
LTC6992-3/LTC6992-4
19
69921234fc
Basic Operation
The simplest and most accurate method to program the
LTC6992 is to use a single resistor, RSET, between the
SET and GND pins. The design procedure is a four step
process. After choosing the proper LTC6992 version and
POL bit setting, select the NDIV value and then calculate
the value for the RSET resistor.
Alternatively, Linear Technology offers the easy to use
TimerBlox Designer tool to quickly design any LTC6992
based circuit. Download the free TimerBlox Designer
software at www.linear.com/timerblox.
Step 1: Selecting the POL Bit Setting
Most applications will use POL = 0, resulting in a positive
transferfunction.However,someapplicationsmayrequire
a negative transfer function, where increasing VMOD re-
duces the output duty cycle. For example, if the LTC6992
is used in a feedback loop, POL = 1 may be required to
achieve negative feedback.
Step 2: Selecting the LTC6992 Version
ThedifferencebetweentheLTC6992versionsisobservedat
the endpoints of the duty cycle control range. Applications
that require the output to never stop oscillating should use
the LTC6992-2. On the other hand, if the output should be
allowed to rest at GND or V+ (0% or 100% duty cycle),
select the LTC6992-1.
The LTC6992-3 and LTC6992-4 clamp the duty cycle at
only one end of the control range, allowing the output to
stop oscillating at the other extreme. If POL = 1 the clamp
will swap from low duty cycle to high, or vice-versa. Refer
to Table 2 and Figure 4 for assistance in selecting the
proper version.
Step 3: Selecting the NDIV Frequency Divider Value
As explained earlier, the voltage on the DIV pin sets the
DIVCODE which determines both the POL bit and the
NDIV value. For a given output frequency, NDIV should be
selected to be within the following range.
62.5kHz
fOUT
≤ NDIV ≤
1MHz
fOUT
(1a)
applicaTions inForMaTion
To minimize supply current, choose the lowest NDIV value
(generallyrecommended).Forfasterstart-upordecreased
jitter,chooseahigherNDIVsetting.Alternatively,useTable1
as a guide to select the best NDIV value for the given ap-
plication.
With POL already chosen, this completes the selection of
DIVCODE. Use Table 1 to select the proper resistor divider
or VDIV/V+ ratio to apply to the DIV pin.
Step 4: Calculate and Select RSET
The final step is to calculate the correct value for RSET
using the following equation.
RSET =
1MHz 50k
NDIV fOUT
(1b)
Select the standard resistor value closest to the calculated
value.
Example: Design a PWM circuit that satisfies the following
requirements:
fOUT = 20kHz
Positive VMOD to duty cycle response
Output can reach 100% duty cycle, but not 0%
Minimum power consumption
Step 1: Selecting the POL Bit Setting
For positive transfer function (duty cycle increases with
VMOD), choose POL = 0.
Step 2: Selecting the LTC6992 Version
To limit the minimum duty cycle, but allow the maximum
duty cycle to reach 100%, choose LTC6992-4. (Note that
if POL = 1 the LTC6992-3 would be the correct choice.)
Step 3: Selecting the NDIV Frequency Divider Value
Choose an NDIV value that meets the requirements of
Equation (1a).
3.125 ≤ NDIV ≤ 50
Potential settings for NDIV include 4 and 16. NDIV = 4 is
the best choice, as it minimizes supply current by us-
相关PDF资料 |
PDF描述 |
|---|---|
| VE-2TF-MY-S | CONVERTER MOD DC/DC 72V 50W |
| VI-B1D-IU-S | CONVERTER MOD DC/DC 85V 200W |
| VE-2T3-MY-S | CONVERTER MOD DC/DC 24V 50W |
| VI-B1B-IU-S | CONVERTER MOD DC/DC 95V 200W |
| VE-25Z-MY-S | CONVERTER MOD DC/DC 2V 20W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC6992CDCB6-1-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:TimerBlox Voltage-Controlled Pulse Width Modulator (PWM) |
| LTC6992CDCB6-1-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:TimerBlox Voltage-Controlled Pulse Width Modulator (PWM) |
| LTC6992CDCB6-2-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:TimerBlox Voltage-Controlled Pulse Width Modulator (PWM) |
| LTC6992CDCB6-2-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:TimerBlox Voltage-Controlled Pulse Width Modulator (PWM) |
| LTC6992CDCB6-3-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:TimerBlox Voltage-Controlled Pulse Width Modulator (PWM) |
发布紧急采购，3分钟左右您将得到回复。