- 您现在的位置：买卖IC网 > PDF目录19745 > LTM8032MPV#PBF (Linear Technology)IC BUCK ADJ 2A 71LGA PDF资料下载
参数资料
| 型号： | LTM8032MPV#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 12/26页 |
| 文件大小： | 0K |
| 描述： | IC BUCK ADJ 2A 71LGA |
| 产品培训模块： | Wide Temperature DC/DC Converter µModules High Voltage µModule DC/DC Regulators Power Module vs. Discrete DC to DC µModule® Family of EN55022 Class B Certified Regulators |
| 软件下载： | LTM8032 Spice Model |
| 产品目录绘图： | LTM Series_9x15x2.8 |
| 设计资源： | DC1386B Design Files LTM8032MPV#PBF Footprint.bxl |
| 特色产品： | μModule Products |
| 标准包装： | 170 |
| 系列： | µModule® |
| 类型： | 非隔离（POL） |
| 输出数： | 1 |
| 电压 - 输入（最小）： | 3.6V |
| 电压 - 输入（最大）： | 36V |
| Voltage - Output 1： | 0.8 ~ 10 V |
| 电流 - 输出（最大）： | 2A |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 71-LGA |
| 尺寸/尺寸： | 0.59" L x 0.35" W x 0.11" H（15.0mm x 9.0mm x 2.8mm） |
| 包装： | 托盘 |
| 工作温度： | -55°C ~ 125°C |
| 产品目录页面： | 2711 (CN2011-ZH PDF) |
LTM8032
APPLICATIONS INFORMATION
than 56V. If BIAS power is applied from a remote or noisy
voltage source, it may be necessary to apply a decoupling
capacitor locally to the LTM8032.
Load Sharing
Two or more LTM8032s may be paralleled to produce higher
currents. This may, however, alter the EMI performance
of the LTM8032s. To do this, tie the V IN , ADJ, V OUT and
SHARE pins of all the paralleled LTM8032s together. To
ensure that paralleled modules start up together, the RUN/
SS pins may be tied together, as well. Synchronize the
LTM8032s to an external clock to eliminate beat frequen-
cies, if required. If the RUN/SS pins are not tied together,
make sure that the same valued soft-start capacitors
are used for each module. An example of two LTM8032
modules configured for load sharing is given in the Typical
Applications section.
To disable Burst Mode operation, tie SYNC to a stable
voltage above 0.7V or synchronize to an external clock.
Do not leave the SYNC pin floating.
Minimum Input Voltage
The LTM8032 is a step-down converter, so a minimum
amount of headroom is required to keep the output in
regulation. In addition, the input voltage required to turn
on is higher than that required to run, and depends upon
whether the RUN/SS is used. As shown in Figure 1, it
takes only about 3.6V IN for the LTM8032 to run a 3.3V
output at light load. If RUN/SS is tied directly to V IN , a
5.5V input voltage is required to start. If V IN is allowed to
settle in the operating region first then the RUN/SS pin is
enabled, the minimum input voltage to start at light load
is lower, about 4.7V. A similar curve for 5V OUT operation
is also provided in Figure 1.
For current sharing applications using multiple LTM8032s,
the ADJ pins for all regulators may be combined using
one resistor to ground as determined by:
196.71
6.0
5.5
5.0
V OUT = 3.3V
R ADJ =
N
V OUT – 0.79
4.5
4.0
where N is the number of paralleled modules and R ADJ
is in kΩ.
Burst Mode Operation
3.5
3.0
0
TO RUN
TO START
RUN/SS ENABLED
500 1000 1500 2000
LOAD CURRENT (mA)
TO RUN
To enhance efficiency at light loads, the LTM8032 auto-
matically switches to Burst Mode operation which keeps
the output capacitor charged to the proper voltage while
minimizing the input quiescent current. During Burst Mode
operation, the LTM8032 delivers single cycle bursts of
current to the output capacitor followed by sleep periods
where the output power is delivered to the load by the output
capacitor. In addition, V IN and BIAS quiescent currents are
reduced to typically 25μA and 60μA respectively during
the sleep time. As the load current decreases towards a
no-load condition, the percentage of time that the LTM8032
operates in sleep mode increases and the average input
current is greatly reduced, resulting in higher efficiency.
Burst Mode operation is enabled by tying SYNC to GND.
8032 F01a
7.5
V OUT = 5V
7.0
6.5
6.0
5.5
TO START
RUN/SS ENABLED
5.0
0 500 1000 1500 2000
LOAD CURRENT (mA)
8032 F01b
Figure 1. The LTM8032 Needs More Voltage to Start Than Run
8032fg
12
For more information www.linear.com/LTM8032
相关PDF资料 |
PDF描述 |
|---|---|
| GCM15DCSD-S288 | CONN EDGECARD 30POS .156 EXTEND |
| VI-2TL-CY-F3 | CONVERTER MOD DC/DC 28V 50W |
| VI-2TL-CY-F2 | CONVERTER MOD DC/DC 28V 50W |
| GCM15DCMN-S288 | CONN EDGECARD 30POS .156 EXTEND |
| LC4256C-10FT256BI | IC PLD 256MC 160IO 10NS 256FTBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTM8032MPY#PBF | 功能描述:IC DC/DC UMODULE 2A 71BGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:66V 电压 - 输入（最大）:160V Voltage - Output 1:12V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:50W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-FinMod 尺寸/尺寸:4.60" L x 1.86" W x 0.79" H（116.8mm x 47.2mm x 20.1mm） 包装:散装 工作温度:-25°C ~ 85°C 效率:* 电源（瓦特）- 最大:* |
| LTM8033 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Ultralow EMI 28VIN, 6A DC/DC μModule Regulator |
| LTM8033EV#PBF | 功能描述:IC DC-DC UMODULE BUCK 3A 76-LGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:55V 电压 - 输入（最大）:100V Voltage - Output 1:5.8V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:100W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9 针半砖 BusMod 尺寸/尺寸:2.36" L x 2.28" W x 1.08" H（59.9mm x 57.9mm x 27.4mm） 包装:散装 工作温度:-25°C ~ 100°C 效率:* 电源（瓦特）- 最大:* |
| LTM8033EVPBF | 制造商:Linear Technology 功能描述:Low Noise EMC 36V 3A DC/DC uModule LGA76 |
| LTM8033EV-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Ultralow Noise EMC 36VIN, 3A DC/DC μModule Regulator |
发布紧急采购，3分钟左右您将得到回复。