- 您现在的位置：买卖IC网 > PDF目录45000 > LTM8052IV#PBF (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PBGA81 PDF资料下载
参数资料
| 型号： | LTM8052IV#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PBGA81 |
| 封装： | 15 X 11.25 MM, 2.82 MM HEIGHT, ROHS COMPLIANT, MO-222, LGA-81 |
| 文件页数： | 2/28页 |
| 文件大小： | 350K |
| 代理商： | LTM8052IV#PBF |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTM8052
10
8052f
pin FuncTions
VOUT (Bank 1): Power Output Pins. Apply the output filter
capacitor and the output load between these pins and
GND pins. When reverse current is being driven into the
LTM8052’soutputbytheload,theenergyisdeliveredback
throughtheLTM8052andouttotheVINpins.Caremustbe
taken to prevent excessive voltage if other devices on the
VIN bus cannot absorb this energy. See Input Precautions
in the Applications Information section for more details
and circuit suggestions.
GND (Bank 2): Tie these GND pins to a local ground plane
below the LTM8052 and the circuit components. In most
applications, the bulk of the heat flow out of the LTM8052
is through these pads, so the printed circuit design has a
large impact on the thermal performance of the part. See
the PCB Layout and Thermal Considerations sections for
moredetails.Returnthefeedbackdivider(RADJ)tothisnet.
VIN(Bank3):TheVINpinssupplycurrenttotheLTM8052’s
internal regulator and to the internal power switches. This
pin must be locally bypassed with an external, low ESR
capacitor; see Table 1 for recommended values.
CTL_T(PinD8):Connectaresistor/NTCthermistornetwork
to the CTL_T pin to reduce the maximum regulated output
current of the LTM8052 in response to temperature. The
maximum control voltage is 1.5V. If this function is not
used, tie this pin to VREF.
CTL_I (Pin E8): The CTL_I pin reduces the maximum
regulated output current of the LTM8052. The maximum
control voltage is 1.5V. If this function is not used, tie
this pin to VREF.
VREF (Pin F8): Buffered 2V Reference Capable of 0.5mA
Drive. It is valid when VIN > 6V and RUN is active high.
RT (Pin G8): The RT pin is used to program the switching
frequency of the LTM8052 by connecting a resistor from
this pin to ground. The Applications Information section of
the data sheet includes a table to determine the resistance
value based on the desired switching frequency. When us-
ing the SYNC function, apply a resistor value equivalent to
20% lower than the clock frequency applied to the SYNC
pin. Do not leave this pin open.
COMP (Pin H8): Compensation Pin. This pin is generally
not used. The LTM8052 is internally compensated, but
some rare situations may arise that require a modifica-
tion to the control loop. This pin connects directly to the
input PWM comparator of the LTM8052. In most cases,
no adjustment is necessary. If this function is not used,
leave this pin open.
SS (Pin J8): Soft-Start Pin. Place an external capacitor to
ground to ramp the output voltage during start-up condi-
tions. The soft-start pin has an 11A charging current.
ADJ(PinK8):TheLTM8052regulatesitsADJpinto1.19V.
Connect the adjust resistor from this pin to ground. The
value of RADJ is given by the equation:
RADJ =
11.9
VOUT –1.19
where RADJ is in kΩ.
RUN (Pin L6): The RUN pin acts as an enable pin and turns
on the internal circuitry. It may also be used to implement
a precision UVLO. See the Applications Information sec-
tion for details. The RUN pin is internally clamped, so it
may be pulled up to a voltage source that is higher than
the absolute maximum voltage of 6V through a resistor,
provided the pin current does not exceed 100A. Do not
leave this pin open.
SYNC (Pin L7): Frequency Synchronization Pin. This pin
allows the switching frequency to be synchronized to an
external clock. The RT resistor should be chosen to oper-
ate the internal clock at 20% lower than the SYNC pulse
frequency. This pin should be grounded when not in use.
Do not leave this pin floating. When laying out the board,
avoid noise coupling to or from the SYNC trace. See the
Synchronization section in Applications Information.
相关PDF资料 |
PDF描述 |
|---|---|
| LTM8062EV#PBF | BATTERY CHARGE CONTROLLER, 1150 kHz SWITCHING FREQ-MAX, PBGA77 |
| LTM8062AEV#PBF | BATTERY CHARGE CONTROLLER, 1150 kHz SWITCHING FREQ-MAX, PBGA77 |
| LTM9005CV-AA#PBF | SPECIALTY ANALOG CIRCUIT, PBGA204 |
| LTM9005CV-AB#PBF | SPECIALTY ANALOG CIRCUIT, PBGA204 |
| LTM9005IV-AB#PBF | SPECIALTY ANALOG CIRCUIT, PBGA204 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTM8061 | 制造商:LINER 制造商全称:Linear Technology 功能描述:32V, 2A μModule Li-Ion/ Polymer Battery Charger |
| LTM8061EV-4.1#PBF | 功能描述:IC BATTERY CHARGER 4.1V 77-LGA RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:µModule® 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTM8061EV-4.1PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:32V, 2A μModule Li-Ion/ Polymer Battery Charger |
| LTM8061EV-4.2#PBF | 功能描述:IC BATTERY CHARGER 4.2V 77-LGA RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:µModule® 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTM8061EV-4.2PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:32V, 2A μModule Li-Ion/ Polymer Battery Charger |
发布紧急采购，3分钟左右您将得到回复。