参数资料
型号: LUCL9219GAR-DT
英文描述: Low-Cost Line Interface with Reverse Battery and Dual Current Limit
中文描述: 低成本线接口,具有反向电池和双电流限制
文件页数: 11/30页
文件大小: 397K
代理商: LUCL9219GAR-DT
Agere Systems Inc.
19
Data Sheet
November 2001
with Reverse Battery and Dual Current Limit
L9219A/G Low-Cost Line Interface
Applications (continued)
dc Applications
Battery Feed
The dc feed characteristic can be described by:
where:
IL = dc loop current.
VT/R = dc loop voltage.
|VBAT| = battery voltage magnitude.
VOH = overhead voltage. This is the difference between
the battery voltage and the open loop tip/ring
voltage.
RL = loop resistance, not including protection resistors.
RP = protection resistor value.
Rdc = SLIC internal dc feed resistance.
Notes:
VBAT = –48 V.
ILIM = 22 mA.
Rdc1 = 80
.
Figure 13. Loop Current vs. Loop Voltage
Starting from the on-hook condition and going through
to a short circuit, the curve passes through the follow-
ing two regions:
Region 1: On-hook and low loop currents. The slope
corresponds to the dc resistance of the
SLIC, Rdc1 (default is 70
typical). The open
circuit voltage is the battery voltage minus
the overhead voltage of the device, VOH
(default is 6.5 V typical). These values are
suitable for most applications, but can be
adjusted if needed. For more information,
see the sections entitled Adjusting dc Feed
Resistance and Adjusting Overhead Voltage.
Region 2: Current limit. The dc current is limited to a
starting value determined by external resis-
tor RPROG, the logic table, an internal current
source, and the gain from tip/ring to pin
VITR.
Current Limit
With the logic inputs set to 11 (a low current limit active
state), current limit with a 100
load is given by the fol-
lowing:
0.637 RPROG (k
) + 2 mA = ILIM x (mA)
Via the logic table, the current limit can be increased a
nominal 42% from the value set by the RPROG resistor.
The relationship between low current limit and high
current limit is as follows:
= 0.7
Overhead Voltage
In order to drive an on-hook ac signal, the SLIC must
set up the tip and ring voltage to a value less than the
battery voltage. The amount that the open loop voltage
is decreased relative to the battery is referred to as the
overhead voltage and is expressed as the following
equation:
VOH = |VBAT| – (VPT – VPR)
Without this buffer voltage, amplifier saturation will
occur and the signal will be clipped. The L9219 is auto-
matically set at the factory to allow undistorted on-hook
transmission of a 3.14 dBm signal into a 900
loop
impedance.
VT/R
VBAT
VOH
() R
× L
RL
2RP
Rdc
++
---------------------------------------------
=
IL
VBAT
VOH
RL
2RP
Rdc
++
----------------------------------
=
010
20
50
0
20
30
40
50
LOOP VOLTAGE (V)
30
40
10
L
O
OP
CURR
ENT
(
m
A
)
1
12.5 k
–1
Rdc1
ILIM TESTED
ILIM ONSET
12-3050 (F).i
ILIMIT
Low
()
ILIMIT
High
()
-----------------------------------
相关PDF资料
PDF描述
LUPXA255A0C200 32-BIT, 200 MHz, MICROPROCESSOR, PBGA256
LUPXA255A0C300 32-BIT, 300 MHz, MICROPROCESSOR, PBGA256
LV100 Voltage Transducer LV 100
LV200-AW Voltage Transducer LV 200-AW/2
LV25-1000 Voltage Transducer LV 25-1000
相关代理商/技术参数
参数描述
LUCL9310AP-D 制造商:AGERE 制造商全称:AGERE 功能描述:Line Interface and Line Access Circuit Full-Feature SLIC,Ringing Relay,and Test Access Device
LUCL9310AP-DT 制造商:AGERE 制造商全称:AGERE 功能描述:Line Interface and Line Access Circuit Full-Feature SLIC,Ringing Relay,and Test Access Device
LUCL9310GP-D 制造商:AGERE 制造商全称:AGERE 功能描述:Line Interface and Line Access Circuit Full-Feature SLIC,Ringing Relay,and Test Access Device
LUCL9310GP-DT 制造商:AGERE 制造商全称:AGERE 功能描述:Line Interface and Line Access Circuit Full-Feature SLIC,Ringing Relay,and Test Access Device
LUCL9311AP-D 制造商:AGERE 制造商全称:AGERE 功能描述:Line Interface and Line Access Circuit Full-Feature SLIC with High Longitudinal Balance, Ringing Relay,and GR-909 Test Access