- 您现在的位置：买卖IC网 > PDF目录95794 > LV8162TT (SANYO SEMICONDUCTOR CO LTD) BRUSH DC MOTOR CONTROLLER, 0.7 A, PDSO12 PDF资料下载
参数资料
| 型号： | LV8162TT |
| 厂商： | SANYO SEMICONDUCTOR CO LTD |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSH DC MOTOR CONTROLLER, 0.7 A, PDSO12 |
| 封装： | 0.150 INCH, MSOP-12 |
| 文件页数： | 5/7页 |
| 文件大小： | 221K |
| 代理商： | LV8162TT |
LV8162TT
No.A1978-5/8
*4 [PWM pin]
Speed control signal input pin.
The PWM pin is pulled up with a 500k resistor inside the IC.
The 500k is used for setting full speed when the PWM pin is open, and if speed control is to be performed by open
collector (open drain) input, it is necessary to pull up the pin using a resistor of an appropriate value.
If speed control is performed using a push-pull input, a pull-up resistor is not required.
When the speed control is performed using the open collector input above, or when push-pull input is used and no
pull-up resistor is used, the IC can be used without a sequence (power supply and PWM input can be turned on in any
order).
It is recommended that a resistor of 1k or more is connected in series to protect the pin against misconnection such as
ground open and reverse connection.
*5 [FG pin]
Rotatinal speed detection pin.
This is open drain output that can detect the rotational speed by the FG output in response to the ohase switching signal.
This pin is held off when in standby mode.
Keep this pin open when it is not to be used.
It is recommended that a resistor of 1k or more is connected in series to protect the pin against misconnection such as
ground open and reverse connection.
*6 [RD pin]
Lock detection pin.
This is open drain output that is low during rotation, off when lockup is detected, and low when in standby mode.
Keep this pin open when it is not to be used.
It is recommended that a resistor of 1k or more is connected in series to protect the pin against misconnection such as
ground open and reverse connection.
*7 [Low current consumption during standby]
The fan motor controlled using this IC can be set to a current consumption of 10A (room temperature, typ.) when in
standby mode. However, note that it will not become 10A under any of the following conditions.
When the Hall element bias current is fed from the power supply
→ The current flowing to the Hall element is increased
When connecting a pull-up resistor to the PWM pin.
→ Because the PWM pin must be set to low when in standby mode, the current flowing to the pull-up resistor is
increased.
When using an RD pin.
→ Because the RD pin is held low when in standby mode, the current flowing to the pull-up resistor is increased.
相关PDF资料 |
PDF描述 |
|---|---|
| LV8227LG | UNIVERSAL MOTOR CONTROLLER, PBGA64 |
| LV8400V | BRUSH DC MOTOR CONTROLLER, PDSO16 |
| LV8401V | BRUSH DC MOTOR CONTROLLER, 3.8 A, PDSO16 |
| LV8402V | BRUSH DC MOTOR CONTROLLER, 2.5 A, PDSO16 |
| LV8405V | BRUSH DC MOTOR CONTROLLER, 2.5 A, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LV8163QA-BH | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LV8169MUTBG | 制造商:ON Semiconductor 功能描述:SINGLE PHASE MOTOR DRIVER - Tape and Reel |
| LV8206T | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:CD and MD System Motor Driver |
| LV-820M2G---2030S | 制造商:Surge Components Inc 功能描述:CAP ALUM 82UF 400V ?20% 2000LHRS 20 X 30 - Bulk |
| LV-820M2G---2225S | 制造商:Surge Components Inc 功能描述:CAP ALUM 82UF 400V ?20% 2000LHRS 22 X 25 - Bulk |
发布紧急采购，3分钟左右您将得到回复。