- 您现在的位置：买卖IC网 > PDF目录67759 > LV8773 (SANYO SEMICONDUCTOR CO LTD) STEPPER MOTOR CONTROLLER, DIP28 PDF资料下载
参数资料
| 型号： | LV8773 |
| 厂商： | SANYO SEMICONDUCTOR CO LTD |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, DIP28 |
| 封装： | 0.500 INCH, DIP-28 |
| 文件页数： | 12/14页 |
| 文件大小： | 183K |
| 代理商： | LV8773 |
LV8773
No.A1961-7/26
Description of operation
(1) Chip enable function
This IC is switched between standby and operating mode by setting the ST pin. In standby mode, the IC is set to
power-save mode and all logic is reset. In addition, the internal regulator circuit and charge pump circuit do not
operate in standby mode.
ST
Mode
Internal regulator
Charge pump
Low or Open
Standby mode
Standby
High
Operating mode
Operating
(2) Output control logic
input
output
mode
DC11(21)
DC12(22)
OUT1(2)A
OUT1(2)B
L
OFF
Stand-by
H
L
H
L
CW ( Forward )
L
H
L
H
CCW ( reverse )
H
L
brake
(3) Blanking period
If, when exercising PWM constant-current chopping control over the motor current, the mode is switched from decay
to charge, the recovery current of the parasitic diode may flow to the current sensing resistance, causing noise to be
carried on the current sensing resistance pin, and this may result in erroneous detection. To prevent this erroneous
detection, a blanking period is provided to prevent the noise occurring during mode switching from being received.
During this period, the mode is not switched from charge to decay even if noise is carried on the current sensing
resistance pin.
This IC is the blanking time is fixed at approximately 2
μs.
(4) Chopping frequency setting
For constant-current control, this IC performs chopping operations at the frequency determined by the capacitor
(Cchop) connected between the CHOP pin and GND.
The chopping frequency is set as shown below by the capacitor (Cchop) connected between the CHOP pin and GND.
Fchop = Ichop/ (Cchop × Vtchop × 2) (Hz)
Ichop : Capacitor charge/discharge current, typ 10
μA
Vtchop : Charge/discharge hysteresis voltage (Vtup-Vtdown), typ 0.5V
For instance, when Cchop is 220pF, the chopping frequency will be as follows :
Fchop = 10
μA/ (220pF × 0.5V × 2) = 45.4kHz
相关PDF资料 |
PDF描述 |
|---|---|
| LX1661CD-TR | 1.5 A SWITCHING CONTROLLER, PDIP16 |
| LX1660CD-TR | 1.5 A SWITCHING CONTROLLER, PDSO16 |
| LX1671-CPW | 1 A SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PDSO38 |
| LX1671-CLQ | 1 A SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PQCC38 |
| LX1671-CPWTR | 1 A SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PDSO38 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LV8773-E | 功能描述:马达/运动/点火控制器和驱动器 PRINTER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LV8773-E | 制造商:ON Semiconductor 功能描述:OPTOCOUPLERS; Leaded Process Compatible:No; Peak Reflow Compatible (260 C):No ;RoHS Compliant: No |
| LV8773GEVB | 功能描述:电源管理IC开发工具 EVM FOR LV8773 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| LV8773Z-E | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LV8800C | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic |
发布紧急采购，3分钟左右您将得到回复。