- 您现在的位置：买卖IC网 > PDF目录67759 > LV8773 (SANYO SEMICONDUCTOR CO LTD) STEPPER MOTOR CONTROLLER, DIP28 PDF资料下载
参数资料
| 型号： | LV8773 |
| 厂商： | SANYO SEMICONDUCTOR CO LTD |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, DIP28 |
| 封装： | 0.500 INCH, DIP-28 |
| 文件页数： | 3/14页 |
| 文件大小： | 183K |
| 代理商： | LV8773 |
LV8773
No.A1961-11/26
(7-3) Auto reset type
In the automatic reset mode, when the output current exceeds the detection current level, the output waveform
changes to the switching waveform.
As with the latch system, when the output short-circuited state is detected, the short-circuit protection circuit is
activated. When the operation of the short-circuit detection circuit exceeds the timer latch time (Tcem) described later,
the output is changed over to the standby mode and is reset to the ON mode again in 2ms (typ). In this event, if the
overcurrent mode still continues, the switching mode described above is repeated until the overcurrent mode is
canceled.
(7-4) Unusual condition warning output pins (EMO1, EMO2)
The LV8773 is provided with the EMO pin which notifies the CPU of an unusual condition if the protection circuit
operates by detecting an unusual condition of the IC. This pin is of the open-drain output type and when an unusual
condition is detected, the EMO output is placed in the ON (EMO = Low) state.
The EMO1 pin and the EMO2 pin output unusual condition on 2ch side/ 1ch side respectively.
Furthermore, the EMO (EMO2) pin is placed in the ON state when one of the following conditions occurs.
1. Shorting-to-power, shorting-to-ground, or shorting-to-load occurs at the output pin and the output short-circuit
protection circuit is activated.
2. The IC junction temperature rises and the thermal protection circuit is activated.
Unusual condition
EMO1
EMO2
Channel 1 short-circuit detected
ON
-
Channel 2 short-circuit detected
-
ON
Overheating condition detected
ON
(7-5) Timer latch time (Tcem)
The time taken for the output to be set to OFF when the output has been short-circuited can be set using capacitor
Ccem, connected between the CEM pin and GND. The value of capacitor Ccem is determined by the formula given
below.
Timer latch : Tcem
Tcem
≈ Ccem × Vtcem/Icem [sec]
Vtcem : Comparator threshold voltage, typ 1V
Icem : CEM pin charge current, typ 10
μA
(8) Charge Pump Circuit
When the ST pin is set High, the charge pump circuit operates and the VG pin voltage is boosted from the VM voltage
to the VM + VREG5 voltage.
Begin the drive of the motor after the time of tONG or more because it doesn't turn on the output if the voltage of the
VG pin is not pressured to VM+4V or more.
VG Pin Voltage Schematic View
tONG
ST
VM+VREG5
VM+4V
VM
VG pin voltage
相关PDF资料 |
PDF描述 |
|---|---|
| LX1661CD-TR | 1.5 A SWITCHING CONTROLLER, PDIP16 |
| LX1660CD-TR | 1.5 A SWITCHING CONTROLLER, PDSO16 |
| LX1671-CPW | 1 A SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PDSO38 |
| LX1671-CLQ | 1 A SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PQCC38 |
| LX1671-CPWTR | 1 A SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PDSO38 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LV8773-E | 功能描述:马达/运动/点火控制器和驱动器 PRINTER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LV8773-E | 制造商:ON Semiconductor 功能描述:OPTOCOUPLERS; Leaded Process Compatible:No; Peak Reflow Compatible (260 C):No ;RoHS Compliant: No |
| LV8773GEVB | 功能描述:电源管理IC开发工具 EVM FOR LV8773 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| LV8773Z-E | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LV8800C | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic |
发布紧急采购，3分钟左右您将得到回复。