参数资料
型号: LX1684CD-TR
厂商: MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP
元件分类: 稳压器
英文描述: 1 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO14
封装: PLASTIC, SOIC-14
文件页数: 8/12页
文件大小: 248K
代理商: LX1684CD-TR
Microsemi
Integrated Products Division
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 5
Copyright
2000
Rev. 1.0c, 2005-03-08
WWW
.Microse
m
i
.CO
M
LX1684
Voltage-Mode PWM Controller
PRODUCTION DATA SHEET
TM
TH EORY OF O PERAT ION
GENERAL DESCRIPTION
The LX1684 is a voltage-mode pulse-width modulation
controller integrated circuit. The internal oscillator and ramp
generator frequency is fixed at 175kHz. The devices have internal
compensation, so that no external compensation is required.
POWER UP AND INITIALIZATION
At power up, the LX1684 monitors the supply voltage to both
the +5V and the VC1 pins (there is no special requirement for the
sequence of the two supplies). Before both supplies reach their
under-voltage lock-out (UVLO) thresholds, the soft-start (SS) pin
is held low to prevent soft-start from beginning; the oscillator
control is disabled and the top MOSFET is kept OFF.
SOFT-START
Once the supplies are above the UVLO threshold, the soft-start
capacitor begins to be charged up by the reference through a 20k
internal resistor. The capacitor voltage at the SS pin rises as a
simple RC circuit. The SS pin is connected to the amplifier's non-
inverting input that controls the output voltage. The output voltage
will follow the SS pin voltage if sufficient charging current is
provided to the output capacitor. The simple RC soft-start allows
the output to rise faster at the beginning and slower at the end of
the soft-start interval. Thus, the required charging current into the
output capacitor is less at the end of the soft-start interval so
decreasing the possibility of an over-current. A comparator
monitors the SS pin voltage and indicates the end of soft-start
when SS pin voltage reaches 95% of VREF .
OVER-CURRENT PROTECTION (OCP) AND HICCUP
The LX1684 uses the RDS(ON) of the upper MOSFET,
together with a resistor (RSET) to set the actual current limit point.
Unlike the LX1681/2 controllers the LX1684 includes the positive
current sense comparator input providing true Kelvin sensing
which is more accurate and offers more noise immunity.
This
Kelvin sensing also simplifies the PCB layout for current sense.
The CSP pin has a useful common mode input range to about 14V.
The comparator senses the current 1s after the top MOSFET is
switched on.
Experiments have shown that the MOSFET drain voltage will
ring for 200-500ns after the gate is turned on. In order to reduce
inaccuracies due to ringing, a 1s blanking delay after gate turn-on
is built into the current sense comparator. This 1us delay reduces
the effectiveness of the current sense comparator when the output
pulse width is below 1us. This can be problem when the set
application output voltage is less than 3.0V with a 12V input.
Under this condition the output current limit protection will not
function properly. This is usually not true with a short circuit
current condition, which causes the on time to be greater than the
blanking delay. In this circumstance the current limit comparator
would turn off the top FET driver.
The comparator draws a current (ISET), whose magnitude is
45A. The set resistor is selected to set the current limit for the
application. When the sensed voltage across the RDS(ON) plus the
set resistor exceeds the 400mV VTRIP threshold, the OCP
comparator outputs a signal to reset the PWM latch and to start
hiccup mode. The soft-start capacitor (CSS) is discharged slowly
(10 times slower than when being charged up by RSS). When the
voltage on the SS/ENABLE pin reaches a 0.3V threshold, hiccup
finishes and the circuit soft-starts again. During hiccup, the top
MOSFET is OFF and the bottom MOSFET remains ON. Hiccup is
disabled during the soft-start interval, allowing the circuit to start
up with the maximum current. If the rise speed of the output
voltage is too fast, the required charging current to the output
capacitor may be higher than the limit-current. In this case, the
peak MOSFET current is regulated to the limit-current by the
current-sense comparator. If the MOSFET current still reaches its
limit after the soft-start finishes, the hiccup is triggered again. The
hiccup ensures the average heat generation on both MOSFET’s and
the average current to be much less than that in normal operation,
if the output has a short circuit. Over-current protection can also be
implemented using a sense resistor, instead of using the RDS(ON)
of the upper MOSFET, for greater set-point accuracy. See
Application Information section.
OSCILLATOR FREQUENCY
An internal oscillator sets the switching frequency at about 175
kHz.
DD
EE
SS
CC
RR
IIPP
TT
IIOO
NN
相关PDF资料
PDF描述
LX1688IPW-TR FLUORESCENT LIGHT CONTROLLER, 70 kHz SWITCHING FREQ-MAX, PDSO24
LX1689IPWT FLUORESCENT LIGHT CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO20
LX1689CPWT FLUORESCENT LIGHT CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO20
LX1691AIPW-TR 0.1 A FLUORESCENT LIGHT CONTROLLER, 250 kHz SWITCHING FREQ-MAX, PDSO16
LX1692BIPW-TR 0.1 A SWITCHING CONTROLLER, PDSO20
相关代理商/技术参数
参数描述
LX1686 制造商:MICROSEMI 制造商全称:Microsemi Corporation 功能描述:Digital Dimming CCFL Controller IC
LX1686CPW 功能描述:IC CTRLR CCFL BACKLIGHT 24TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 照明,镇流器控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:CCFL 控制器 频率:40 ~ 80 kHz 电流 - 电源:5mA 电流 - 输出:- 电源电压:4.5 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:16-SOIC(0.154",3.90mm 宽) 供应商设备封装:16-SOIC 包装:带卷 (TR) 其它名称:90-3991V+V01
LX1686CPWT 制造商:未知厂家 制造商全称:未知厂家 功能描述:Ballast/Backlight Controller/Driver
LX1686CPW-TR 制造商:Microsemi Corporation 功能描述:CCFL Controller 3.3V/5V 24-Pin TSSOP T/R
LX1686E 制造商:MICROSEMI 制造商全称:Microsemi Corporation 功能描述:Digital Dimming CCFL Controller IC