- 您现在的位置：买卖IC网 > PDF目录369885 > LXT334&LXT304A LXT334 & LXT304A - LXT334 & LXT304A ?Low Cost & High Performance Quad E1 Interface Solution PDF资料下载
参数资料
| 型号： | LXT334&LXT304A |
| 英文描述： | LXT334 & LXT304A - LXT334 & LXT304A ?Low Cost & High Performance Quad E1 Interface Solution |
| 中文描述： | LXT334 |
| 文件页数： | 12/32页 |
| 文件大小： | 395K |
| 代理商： | LXT334&LXT304A |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LXT331
—
Dual T1/E1 Line Interface Unit
12
Datasheet
2. Pulse width: the monitor distinguishes between marks and noise pulses by the pulse width.
LXT331 requires a mark pulse to be at least 120 ns wide (typical).
As shown in
Figure 4 on page 13
, there are two type of marks:
“
A
”
and
“
B
”
. C1 and C2 detect
“
A
”
marks while the AND gate (A1) ensures that both mark signals are present at the same time. If the
pulse widths are adequate, i.e. both a positive mark on MTIP and a negative mark on MRING, the
A1 output goes High. Likewise C3 and C4 detect
“
B
”
marks. If the pulse meets the minimum width
requirement, the AND gate (A2) output goes High when there are both a negative mark on MTIP
and a positive mark on MRING. The OR gate (O1) passes the mark, as the signal
“
zero
”
, on to the
clock/counter circuit which controls the DPM output.
A latch samples the counter and goes High if the DPM circuit sees 63 consecutive zeros. Any mark
resets the counter. The DPM signal goes High after the 63
rd
zero.
2.2.3
Driver Failure Monitor
The transceiver incorporates an internal Driver Failure Monitor (DFM) that observes TTIP and
TRING. Driver failure is detected with a capacitor that is charged as a function of driver output
current, and discharged as a measure of the maximum allowable current. Shorted lines draw excess
current, overcharging the cap. When the capacitor charge deviates outside the nominal charge
window, a driver failure is reported. In Host mode the DFM bit is set in the serial word. In both
Hardware and Host modes the DFM pin goes High. During a long string of spaces, a short-induced
overcharge eventually bleeds off, clearing the DFM flag.
2.3
Control Modes
The LXT331 transceiver operates in either standalone Hardware mode (default) or Host mode. In
Host mode a microprocessor controls the LXT331 via the serial I/O port (SIO) which provides
common access to both LIUs. In Hardware mode, the transceiver is controlled through individual
pins; a microprocessor is not required.
Table 2. Equalizer Control Inputs - Hardware Mode
1
LEN2
LEN1
LEN0
Line Length
2
Cable Loss
3
Application
Frequency
Low
High
High
High
High
High
Low
Low
High
High
High
Low
High
Low
High
0 - 133 ft ABAM
133-266 ft ABAM
266-399 ft ABAM
399-533 ft ABAM
533-655 ft ABAM
0.6 dB
1.2 dB
1.8 dB
2.4 dB
3.0 dB
DSX-1
1.544 MHz
Low
Low
Low
Low
Low
High
ITU Recommendation G.703
E1 - Coax (75
)
E1 - Twisted-pair (120
)
2.048 MHz
Low
High
Low
FCC Part 68, Option A
CSU
1.544 MHz
1. LEN0-2 inputs are shown as High or Low for Hardware mode. For Host mode serial inputs, High = 1 and
Low = 0.
2. Line length from LXT331 to DSX-1 cross-connect point.
3. Maximum cable loss at 772 kHz.
相关PDF资料 |
PDF描述 |
|---|---|
| LXT336QE | PCM RECEIVER|QUAD|CEPT PCM-30/E-1|CMOS|QFP|64PIN|PLASTIC |
| LXT350PE | PCM TRANSCEIVER|SINGLE|CEPT PCM-30/E-1|CMOS|LDCC|28PIN|PLASTIC |
| LXT361LE | Telecommunication IC |
| LXT361PE | Telecommunication IC |
| LXT362LE | PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|QFP|44PIN|PLASTIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LXT335 | 制造商:LVL1 制造商全称:LVL1 功能描述:Quad Short Haul PCM Analog Interface |
| LXT336QE | 制造商:未知厂家 制造商全称:未知厂家 功能描述:PCM RECEIVER|QUAD|CEPT PCM-30/E-1|CMOS|QFP|64PIN|PLASTIC |
| LXT350 | 制造商:LVL1 制造商全称:LVL1 功能描述:Integrated T1/E1 S/H Transceivers With Crystal-less Jitter Attenuation |
| LXT350PE | 制造商:Intel 功能描述: |
| LXT350QE | 制造商:LEVEL1 功能描述: |
发布紧急采购，3分钟左右您将得到回复。