- 您现在的位置：买卖IC网 > PDF目录377808 > M28W160BT85GBT (意法半导体) 16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory PDF资料下载
参数资料
| 型号： | M28W160BT85GBT |
| 厂商： | 意法半导体 |
| 英文描述： | 16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory |
| 中文描述： | 16兆位（1兆x16插槽，引导块）3V电源快闪记忆体 |
| 文件页数： | 11/45页 |
| 文件大小： | 343K |
| 代理商： | M28W160BT85GBT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页
11/45
M28W160BT, M28W160BB
BUS OPERATIONS
There are six standard bus operations that control
the device. These are Bus Read, Bus Write, Out-
put Disable, Standby, Automatic Standby and Re-
set. See Table 2, Bus Operations, for a summary.
Typically glitches of less than 5ns on Chip Enable
or Write Enable are ignored by the memory and do
not affect bus operations.
Read.
Read Bus operations are used to output
the contents of the Memory Array, the Electronic
Signature, the Status Register and the Common
Flash Interface. Both Chip Enable and Output En-
able must be at V
IL
in order to perform a read op-
eration. The Chip Enable input should be used to
enable the device. Output Enable should be used
to gate data onto the output. The data read de-
pends on the previous command written to the
memory (see Command Interface section). See
Figure 9, Read Mode AC Waveforms, and Table
12, Read AC Characteristics, for details of when
the output becomes valid.
Read mode is the default state of the device when
exiting Reset or after power-up.
Write.
Bus Write operations write Commands to
the memory or latch Input Data to be programmed.
A write operation is initiated when Chip Enable
and Write Enable are at V
IL
with Output Enable at
V
IH
. Commands, Input Data and Addresses are
latched on the rising edge of Write Enable or Chip
Enable, whichever occurs first.
See Figures 10 and 11, Write AC Waveforms, and
Tables 13 and 14, Write AC Characteristics, for
details of the timing requirements.
Output Disable.
The data outputs are high im-
pedance when the Output Enable is at V
IH
.
Standby.
Standby disables most of the internal
circuitry allowing a substantial reduction of the cur-
rent consumption. The memory is in stand-by
when Chip Enable is at V
IH
and the device is in
read mode. The power consumption is reduced to
the stand-by level and the outputs are set to high
impedance, independently from the Output Enable
or Write Enable inputs. If Chip Enable switches to
V
IH
during a program or erase operation, the de-
vice enters Standby mode when finished.
Automatic Standby.
Automatic
vides a low power consumption state during Read
mode. Following a read operation, the device en-
ters Automatic Standby after 150ns of bus inactiv-
ity, even if Chip Enable is low, V
IL
, and the supply
current is reduced to I
DD1
. The data Inputs/Out-
puts will still output data.
Reset.
During Reset mode, when Output Enable
is low, V
IL
, the memory is deselected and the out-
puts are high impedance. The memory is in Reset
mode when Reset is at V
IL
. The power consump-
tion is reduced to the Standby level, independently
from the Chip Enable, Output Enable or Write En-
able inputs. If Reset is pulled to V
SS
during a Pro-
gram or Erase, this operation is aborted and the
memory content is no longer valid.
Standby
pro-
Table 2. Bus Operations
Note: X = V
IL
or V
IH
, V
PPH
= 12V ± 5%.
Operation
E
G
W
RP
WP
V
PP
DQ0-DQ15
Read
V
IL
V
IL
V
IH
V
IH
X
Don't Care
Data Output
Write
V
IL
V
IH
V
IL
V
IH
X
V
DD
or V
PPH
Data Input
Output Disable
V
IL
V
IH
V
IH
V
IH
X
Don't Care
Hi-Z
Standby
V
IH
X
X
V
IH
X
Don't Care
Hi-Z
Reset
X
X
X
V
IL
X
Don't Care
Hi-Z
相关PDF资料 |
PDF描述 |
|---|---|
| M28W160BT85-NT | 16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory |
| M28W160BT906T | 16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory |
| M28W160BT90GBT | 16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory |
| M28W160BT90-NT | 16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory |
| M28W160CB100N6T | 16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M28W160BT85N1T | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory |
| M28W160BT85N6T | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory |
| M28W160BT85-NT | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory |
| M28W160BT85ZB1T | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory |
| M28W160BT85ZB6T | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:16 Mbit (1Mb x16, Boot Block) 3V Supply Flash Memory |
发布紧急采购，3分钟左右您将得到回复。