收藏本站
参数资料
型号： M28W800BT10N1T
厂商： 意法半导体
英文描述： 8 Mbit 512Kb x16, Boot Block 3V Supply Flash Memory
中文描述： 8兆位512KB的x16插槽，启动块3V电源快闪记忆体
文件页数： 10/49页
文件大小： 369K
代理商： M28W800BT10N1T
M28W800CT, M28W800CB
10/49
BUS OPERATIONS
There are six standard bus operations that control
the device. These are Bus Read, Bus Write, Out-
put Disable, Standby, Automatic Standby and Re-
set. See Table 2, Bus Operations, for a summary.
Typically glitches of less than 5ns on Chip Enable
or Write Enable are ignored by the memory and do
not affect bus operations.
Read.
Read Bus operations are used to output
the contents of the Memory Array, the Electronic
Signature, the Status Register and the Common
Flash Interface. Both Chip Enable and Output En-
able must be at V
IL
in order to perform a read op-
eration. The Chip Enable input should be used to
enable the device. Output Enable should be used
to gate data onto the output. The data read de-
pends on the previous command written to the
memory (see Command Interface section). See
Figure 9, Read Mode AC Waveforms, and Table
15, Read AC Characteristics, for details of when
the output becomes valid.
Read mode is the default state of the device when
exiting Reset or after power-up.
Write.
Bus Write operations write Commands to
the memory or latch Input Data to be programmed.
A write operation is initiated when Chip Enable
and Write Enable are at V
IL
with Output Enable at
V
IH
. Commands, Input Data and Addresses are
latched on the rising edge of Write Enable or Chip
Enable, whichever occurs first.
See Figures 10 and 11, Write AC Waveforms, and
Tables 16 and 17, Write AC Characteristics, for
details of the timing requirements.
Output Disable.
The data outputs are high im-
pedance when the Output Enable is at V
IH
.
Standby.
Standby disables most of the internal
circuitry allowing a substantial reduction of the cur-
rent consumption. The memory is in stand-by
when Chip Enable is at V
IH
and the device is in
read mode. The power consumption is reduced to
the stand-by level and the outputs are set to high
impedance, independently from the Output Enable
or Write Enable inputs. If Chip Enable switches to
V
IH
during a program or erase operation, the de-
vice enters Standby mode when finished.
Automatic Standby.
Automatic
vides a low power consumption state during Read
mode. Following a read operation, the device en-
ters Automatic Standby after 150ns of bus inactiv-
ity even if Chip Enable is Low, V
IL
, and the supply
current is reduced to I
DD1
. The data Inputs/Out-
puts will still output data if a bus Read operation is
in progress.
Reset.
During Reset mode when Output Enable
is Low, V
IL
, the memory is deselected and the out-
puts are high impedance. The memory is in Reset
mode when Reset is at V
IL
. The power consump-
tion is reduced to the Standby level, independently
from the Chip Enable, Output Enable or Write En-
able inputs. If Reset is pulled to V
SS
during a Pro-
gram or Erase, this operation is aborted and the
memory content is no longer valid.
Standby
pro-
Table 2. Bus Operations
Note: X = V
IL
or V
IH
, V
PPH
= 12V ± 5%.
Operation
E
G
W
RP
WP
V
PP
DQ0-DQ15
Bus Read
V
IL
V
IL
V
IH
V
IH
X
Don't Care
Data Output
Bus Write
V
IL
V
IH
V
IL
V
IH
X
V
DD
or V
PPH
Data Input
Output Disable
V
IL
V
IH
V
IH
V
IH
X
Don't Care
Hi-Z
Standby
V
IH
X
X
V
IH
X
Don't Care
Hi-Z
Reset
X
X
X
V
IL
X
Don't Care
Hi-Z
相关PDF资料
PDF描述
M28W800BT 8 Mbit 512Kb x16, Boot Block 3V Supply Flash Memory
M28W800BB85ZB1T 8 Mbit 512Kb x16, Boot Block 3V Supply Flash Memory
M28W800BT85ZB1T 8 Mbit 512Kb x16, Boot Block 3V Supply Flash Memory
M293B1 EPM 32 ELECTRONIC PROGRAM MEMORY FOR 32 STATIONS
M295V002T-120XP1TR 2 Mbit 256Kb x8, Boot Block Single Supply Flash Memory
相关代理商/技术参数
参数描述
M28W800BT90N6 制造商:Micron Technology Inc 功能描述:FLASH PARALLEL 3V/3.3V 8MBIT 512KX16 90NS 48TSOP - Trays
M28W800CB90N1 功能描述:闪存 8M (512Kx16) 90ns RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
M28W800CB90N6 功能描述:闪存 8M (512Kx16) 90ns RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
M28W800CB90N6T 功能描述:闪存 8M (512Kx16) 90ns RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
M28W800CT70N6 功能描述:闪存 8M (512Kx16) 70ns RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*