- 您现在的位置：买卖IC网 > PDF目录67761 > M34519E8FP 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO42 PDF资料下载
参数资料
| 型号： | M34519E8FP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO42 |
| 封装： | 0.450 INCH, 0.80 MM PITCH, PLASTIC, SSOP-42 |
| 文件页数： | 22/50页 |
| 文件大小： | 1808K |
| 代理商： | M34519E8FP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
29
9571B–AT42–08/10
AT42QT1111-MU/AT42QT1111-AU
7.2
Setting Individual Settings
To set up an individual setup value, the host sends the command listed under the “Set
Command” column in Table 7-1, followed by a byte of data.
For details of the communication flow, see Section4.1 on page10.
7.3
Setting All the Setups
The host can send all 42 bytes of setup data to the QT1111 as a block using the Send Setups
command. See Section 5.2 on page 22 for details.
7.4
Address 0: Device Mode
The Device Mode controls the overall operation of the device: number of keys, acquisition
method, timing and trigger mechanism.
KEY_AC: selects the trigger source to start key acquisition; 0 = SYNC pin, 1 = timed.
MODE: selects 7-key or 11-key mode; 0 = default 7-key mode, 1 = 11-key mode.
SIGNAL: selects serial or parallel acquisition of keys signals; 0 = serial, 1 = parallel.
SYNC: selects the trigger type when SYNC Pin is selected as the trigger to start key acquisition.
0 = Level
Acquisition starts when a “0” is read at the SYNC pin. If the pin is held
low, the QT1111 operates in “Free run” mode (that is, it will not sleep in
between acquisitions, but start again immediately).
1 = Edge
Acquisition starts when a rising edge is detected at the SYNC pin.
When acquisition and post-processing are completed, the device
sleeps until another rising edge is detected at the SYNC pin.
32
Key1 Negative Drift Compensation (NDRIFT)/Negative Recalibration Delay (NRD)
0xB1
0xF1
33
Key2 Negative Drift Compensation (NDRIFT)/Negative Recalibration Delay (NRD)
0xB2
0xF2
34
Key3 Negative Drift Compensation (NDRIFT)/Negative Recalibration Delay (NRD)
0xB3
0xF3
35
Key4 Negative Drift Compensation (NDRIFT)/Negative Recalibration Delay (NRD)
0xB4
0xF4
36
Key5 Negative Drift Compensation (NDRIFT)/Negative Recalibration Delay (NRD)
0xB5
0xF5
37
Key6 Negative Drift Compensation (NDRIFT)/Negative Recalibration Delay (NRD)
0xB6
0xF6
38
Key7 Negative Drift Compensation (NDRIFT)/Negative Recalibration Delay (NRD)
0xB7
0xF7
39
Key8 Negative Drift Compensation (NDRIFT)/Negative Recalibration Delay (NRD)
0xB8
0xF8
40
Key9 Negative Drift Compensation (NDRIFT)/Negative Recalibration Delay (NRD)
0xB9
0xF9
41
Key10 Negative Drift Compensation (NDRIFT)/Negative Recalibration Delay (NRD)
0xBA
0xFA
Table 7-1.
Memory Map (Continued)
Address
Function
Set Command
Get Command
Table 7-2.
Device Mode
Address
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
KEY_AC
MODE
SIGNAL
SYNC
REPEAT_TIME
相关PDF资料 |
PDF描述 |
|---|---|
| M34519M8-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO42 |
| M34519M6-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO42 |
| M34553M8H-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP48 |
| M34553M4-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP48 |
| M34553G8HFP | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M34519M6-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:4-BIT CISC SINGLE-CHIP MICROCOMPUTER 720 FAMILY / 4500 SERIES |
| M34519M8-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:4-BIT CISC SINGLE-CHIP MICROCOMPUTER 720 FAMILY / 4500 SERIES |
| M34-52 | 制造商:GAMEWELL-FCI 制造商全称:GAMEWELL-FCI 功能描述:Three-Fold Fire Alarm Boxes and Transmitters |
| M34524EDFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34524M8-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。